ASTM_F_1196_-_00_2013.pdf

Designation:F119600(Reapproved 2013)An American National StandardStandard Specification forSliding Watertight Door Assemblies1This standard is issued under the fixed designation F1196;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers the design,manufacture,andtesting of sliding watertight door assemblies intended to ensurethe watertight integrity of personnel access openings in water-tight bulkheads.1.2 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.2.Referenced Documents2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelF1197 Specification for Sliding Watertight Door ControlSystems2.2 Military Specification:MIL-S-901 Shock Test,H.I.(High Impact);ShipboardMachinery,Equipment and Systems,Requirements for32.3 American Bureau of Shipping:Rules for Building and Classing Steel Vessels42.4 Code of Federal Regulations:5Title 46,Part 159.010,Independent Laboratory:Acceptance,Listing and TerminationTitle 46,Part 163.001,Doors,Watertight,Sliding(and DoorControls),for Merchant Vessels(through the 1991 edition)2.5 International Maritime Organization(IMO):International Code for the Application of Fire Test Proce-dures(FTP)63.Terminology3.1 Definitions:3.1.1 door assemblya door panel and its associated panelstiffening.3.1.2 frame assemblya rigid frame designed to be attachedto a watertight bulkhead.The guide tracks necessary to ensureproper door and frame alignment are also included as part ofthe frame assembly.3.1.3 horizontal sliding watertight doora sliding water-tight door that opens and closes with a horizontal movement.3.1.4 opening handthe direction in which a horizontalsliding watertight door opens.A left-hand opening door opensto the left when viewed from the side of the bulkhead on whichthe door assembly is located.A right-hand opening door opensto the right when viewed from the side of the bulkhead onwhich the door assembly is located.3.1.5 pressure headthe pressure which a sliding watertightdoor assembly is designed to withstand.For a door locatedbelow the bulkhead deck,it is equivalent to the pressureexerted by a column of water the height of which is equal to thevertical distance from the bulkhead deck to the door sill in itsinstalled location.For a door located above the bulkhead deck,it is equivalent to the pressure exerted by the maximum head ofwater for its location,as determined in the damage stabilitycalculations.3.1.6 sliding watertight door assemblya steel door assem-bly and a steel frame assembly fitted with a replaceableinterface between the two that ensures watertightness betweendoor and frame at the design pressure head.3.1.7 vertical sliding watertight doora sliding watertightdoor that opens and closes with a vertical movement.4.Classification4.1 Sliding watertight doors consist of four types:1This specification is under the jurisdiction of Committee F25 on Ships andMarine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved May 1,2013.Published May 2013.Originallyapproved in 1989.Last previous edition approved in 2008 as F1196-00(2008).DOI:10.1520/F1196-00R13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/www.dodssp.daps.mil.4Available from American Bureau of Shipping(ABS),ABS Plaza,16855Northchase Dr.,Houston,TX 77060,http:/www.eagle.org.5Available from U.S.Government Printing Office Superintendent of Documents,732 N.Capitol St.,NW,Mail Stop:SDE,Washington,DC 20401,http:/www.access.gpo.gov.6Available from the International Maritime Organization,4Albert Embankment,London,SE1 7SR UK.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.1.1 Type IAHorizontal doors that conform to the sizesspecified in Table 1 as illustrated in Fig.1.4.1.2 Type IBVertical doors that conform to the sizesspecified in Table 2 as illustrated in Fig.2.4.1.3 Type IIAHorizontal doors that conform generally tothe requirements of this specification,but that necessitatespecial requirements as indicated in Section 5.4.1.4 Type IIBVertical doors that conform generally to therequirements of this specification,but that necessitate specialrequirements as indicated in Section 5.4.2 Watertight doors consist of three classes:NOTE1These classifications are in agreement with those defined andaccepted by the International Conventi