分享
ASTM_A_761_-_A_761M_-_17.pdf
下载文档

ID:187760

大小:281.21KB

页数:12页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_A_761_ _A_761M_ _17
Designation:A761/A761M17American Association State Highway and TransportationOfficials StandardAASHTO No.M 167 M 167 MStandard Specification forCorrugated Steel Structural Plate,Zinc-Coated,for Field-Bolted Pipe,Pipe-Arches,and Arches1This standard is issued under the fixed designation A761/A761M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification covers corrugated steel structuralplate,zinc-coated,used in the construction of pipe,pipe-arches,arches,underpasses,and special shapes for field assem-bly.Appropriate fasteners and accessory materials are alsodescribed.The pipe,arches,and other shapes are generallyused for drainage purposes,pedestrian and vehicularunderpasses,and utility tunnels.1.2 This specification does not include requirements forbedding,backfill,or the relationship between earth cover loadand plate thickness of the pipe.Experience has shown that thesuccessful performance of this product depends upon theproper selection of plate thickness,type of bedding andbackfill,manufacture in the plant,and care in the installation.The purchaser must correlate the preceding factors and also thecorrosion and abrasion requirements of the field installationwith the plate thickness.The structural design of corrugatedsteel structural plate pipe and the proper installation proceduresare described in Practices A796/A796M and A807/A807M.1.3 This specification is applicable to orders in eitherinch-pound units(as A761)or SI units(as A761M).Inch-pound units and SI units are not necessarily equivalent.SI unitsare shown in brackets in the text,but they are the applicablevalues when the material is ordered to A761M.1.4 This specification references notes and footnotes whichprovide explanatory material.These notes and footnotes(ex-cluding those in tables and figures)shall not be considered asrequirements of this specification.2.Referenced Documents2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelA90/A90M Test Method for Weight Mass of Coating onIron and Steel Articles with Zinc or Zinc-Alloy CoatingsA123/A123M Specification for Zinc(Hot-Dip Galvanized)Coatings on Iron and Steel ProductsA153/A153M Specification for Zinc Coating(Hot-Dip)onIron and Steel HardwareA307 Specification for Carbon Steel Bolts,Studs,andThreaded Rod 60 000 PSI Tensile StrengthA370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA449 Specification for Hex Cap Screws,Bolts and Studs,Steel,Heat Treated,120/105/90 ksi Minimum TensileStrength,General UseA563 Specification for Carbon and Alloy Steel NutsA563M Specification for Carbon andAlloy Steel Nuts(Met-ric)A751 Test Methods,Practices,and Terminology for Chemi-cal Analysis of Steel ProductsA754/A754M Test Method for Coating Weight(Mass)ofMetallic Coatings on Steel by X-Ray FluorescenceA780 Practice for Repair of Damaged and Uncoated Areasof Hot-Dip Galvanized CoatingsA796/A796M Practice for Structural Design of CorrugatedSteel Pipe,Pipe-Arches,and Arches for Storm and Sani-tary Sewers and Other Buried ApplicationsA807/A807M Practice for Installing Corrugated Steel Struc-tural Plate Pipe for Sewers and Other ApplicationsA902 Terminology Relating to Metallic Coated Steel Prod-ucts1This specification is under the jurisdiction of ASTM Committee A05 onMetallic-Coated Iron and Steel Products and is the direct responsibility ofSubcommittee A05.17 on Corrugated Steel Pipe Specifications.Current edition approved Feb.1,2017.Published February 2017.Originallyapproved in 1979.Last previous edition approved in 2016 as A761/A761M 16a.DOI:10.1520/A0761_A0761M-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 B6 Specification for ZincB695 Specification for Coatings of Zinc Mechanically De-posited on Iron and SteelE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE376 Practice for Measuring Coating Thickness byMagnetic-Field or Eddy-Current(Electromagnetic)Test-ing MethodsF568M Specification for Carbon and Alloy Ste

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开