分享
ASTM_A_146_-_04_2014.pdf
下载文档

ID:187639

大小:64.69KB

页数:2页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_A_146_ _04_2014
Designation:A14604(Reapproved 2014)Standard Specification forMolybdenum Oxide Products1This standard is issued under the fixed designation A146;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers four grades of molybdenumoxide,designated as A,B1,B2,and molybdic oxide briquets.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2.Referenced Documents2.1 ASTM Standards:2A1025 Specification for Ferroalloys and Other AlloyingMaterials,General Requirements3.General Conditions for Delivery3.1 Materials furnished to this specification shall conform tothe requirements of Specification A1025,including any supple-mentary requirements that are indicated in the purchase order.Failure to comply with the general requirements of Specifica-tion A1025 constitutes nonconformance with this specification.In case of conflict between the requirements of this specifica-tion and Specification A1025,this specification shall prevail.4.Chemical Requirements4.1 The various grades shall conform to the requirements asto chemical composition specified in Table 1.4.2 The manufacturer shall furnish an analysis of eachshipment showing the percentage of each element specified.5.Sampling5.1 Sampling Small BagsWhen packed in the standard-ized small packages,each holding contained molybdenum,thematerial shall be sampled by selecting at random one twentiethof the bags that may bear the same manufacturing lot number,and the combined content of these bags shall be reduced andanalyzed as a separate sample.When a shipment cannot bedivided by lot numbers,one twentieth of the total number ofbags constituting the shipment shall be selected and treated asone sample.The material forming a sample shall be crushed ifnecessary,and in any event passed through a No.10(2.00-mm)sieve.The sample after sieving shall be thoroughly mixed byconing and then reduced to about 2 lb(0.9 kg)by quartering orby means of a riffle sampler.The reduced sample shall then becrushed and passed through a No.60(250-m)sieve.Thesample after sieving shall again be mixed by coning and thendivided through a riffle,preferably a Jones divider,into therequired number of analytical samples.5.2 Sampling Large ContainersWhen packed in drums orlarge bags or cartons,the material shall be sampled by selectingabout one twentieth of the content of each package that maybear the same manufacturing lot number,and the combinedmaterial selected shall be reduced and analyzed as a separatesample.When a shipment cannot be divided by lot numbers,about one twentieth of the content of each package in theshipment shall be selected,and the combined material selectedshall be treated as one sample.The material comprising asample shall be thoroughly mixed by coning and reduced byhalf-shoveling,alternating the operations until the residualweight reaches about 40 lb(18.1 kg).Segregation of sizes shallbe carefully avoided.The sample thus reduced shall becrushed,if necessary,to pass through a No.10(2.00-mm)sieve,and the subsequent sampling procedure shall be asprescribed in 5.1.5.3 Correcting Sample to Dry Net WeightAbsorption ofmoisture by the material would depress the analytical percent-ages with respect to the dry basis,on which the product wasanalyzed when packaged.Accordingly,any analytical sampleshall be dried at 110C,before analysis,and the samplersmoist net weight of the shipment,of a manufacturing lot,or ofany constituent package shall be appropriately corrected to thecorresponding dry weight,thus leading to the proper weight ofcontained molybdenum.6.Keywords6.1 molybdenum;molybdenum oxide1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.18 on Castings.Current edition approved Oct.1,2014.Published October 2014.Originallyapproved in 1932.Last previous edition approved in 2009 as A146 04(2009).Replaces A146 63 T.DOI:10.1520/A0146-04R14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 SUPPLEMENTARY REQUIREMENTSS1.The composition shall be further limited by the requirements of Table S1.1 in addition to thosein Table 1.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this stand

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开