ASTM_A_1111_-_18.pdf

Designation:A111118Standard Specification forCast Iron Closet Flanges for Use With Cast Iron Soil Pipeand Fittings in Gravity Flow Plumbing Drain,Waste,andVent Sanitary Applications1This standard is issued under the fixed designation A1111;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers cast iron soil closet flanges foruse in gravity flow plumbing drain,waste,and vent sanitaryapplications.It establishes standards covering material,manufacture,mechanical and chemical properties,coating,testmethods,inspection,certification,productmarkings,dimensions,and dimensional tolerances for closet flanges.These closet flanges are not intended for pressure applications,as the selection of the proper size for sanitary drain,waste,vent,and storm drain systems allows free air space for gravitydrainage1.2 The EDP/ASA numbers indicated in this section repre-sent a Uniform Industry Code adopted by theAmerican SupplyAssociation(ASA).A group designation prefix,022,is as-signed to hubless products followed by the four-digit identifi-cation assigned to individual items and a check digit.Thissystem has been instituted to facilitate EDP control throughdistribution channels,and is to be used universally in orderingand specifying product items.Those items with no EDPnumbers are either new,special,or transitory and will beassigned numbers on subsequent prints of this specification.1.3 This specification covers closet flanges of the followingpatterns(7.1.1)and,when so designated,shall apply to anyother patterns that conform with the applicable requirementsgiven in this specification.1.4 The values stated in inch-pound units are to be regardedas standard.The values given in brackets are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2A48/A48M Specification for Gray Iron CastingsA74 Specification for Cast Iron Soil Pipe and FittingsA644 Terminology Relating to Iron CastingsA888 Specification for Hubless Cast Iron Soil Pipe andFittings for Sanitary and Storm Drain,Waste,and VentPiping ApplicationsC564 Specification for Rubber Gaskets for Cast Iron SoilPipe and FittingsD3960 Practice for Determining Volatile Organic Compound(VOC)Content of Paints and Related CoatingsE8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE1645 Practice for Preparation of Dried Paint Samples byHotplate or Microwave Digestion for Subsequent LeadAnalysisE2349 Practice for Safety Requirements in Metal CastingOperations:Sand Preparation,Molding,and Core Mak-ing;Melting and Pouring;and Cleaning and Finishing2.2 Federal Standard:3Fed.Std.No.123 Marking for Shipment(Civil Agencies)2.3 Military Standard:4MIL-STD-129 Marking for Shipment and Storage3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 closet flange,na flange used to connect a watercloset to the sanitary piping in drain waste and vent applica-tions.1This specification is under the jurisdiction of ASTM Committee A04 on IronCastings and is the direct responsibility of Subcommittee A04.12 on Pipes andTubes.Current edition approved Nov.15,2018.Published January 2019.Originallyapproved in 2018.DOI:10.1520/A1111-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from General Services Administration Vendor Support Center,https:/vsc.gsa.gov/administration/files/FEDSTD123H.pdf.4Available from General Services Administration Vendor Support Center,https:/vsc.gsa.gov/administration/files/MIL-STD-129R.pdf.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.1.2 manufacturer,nthe entity that casts the closetflanges covered by this standard.4.Materials and Manufacture4.1 The closet flanges shall be iron castings suitable forinstallation and service for sanitary drain,waste,and ventpiping applications.The closet flanges shall meet all applicablereq