ASTM_B_829_-_04a_2017.pdf

Designation:B82904a(Reapproved 2017)Standard Specification forGeneral Requirements for Nickel and Nickel AlloysSeamless Pipe and Tube1This standard is issued under the fixed designation B829;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification contains various requirements that,with the exception of Sections 5 and 10,are mandatoryrequirements to the following ASTM nickel and nickel alloy,seamless pipe and tube specifications:Title of SpecificationASTMDesignation2Nickel Seamless Pipe and TubeB161Seamless Nickel and Nickel Alloy,Condenser and Heat Ex-changer TubesB163Nickel-Copper Alloy(UNS N04400)Seamless Pipe and TubeB165Nickel-Chromium-Iron Alloys(UNS N06600,N06601,andN06690)Seamless Pipe and TubeB167Nickel-Iron-Chromium Alloy Seamless Pipe and TubeB407Nickel-Iron-Chromium-Molybdenum-Copper Alloy(UNS N08825and N08221)Seamless Pipe and TubeB423Nickel-Chromium-Molybdenum-Columbium Alloys(UNSN06625)Pipe and TubeB444Nickel-Chromium-Iron-Columbium-Molybdenum-Tungsten Alloy(UNS N06102)Seamless Pipe and TubeB445Nickel-Iron-Chromium-Silicon Alloys(UNS N08330 and UNSN08332)Seamless PipeB535Copper-Beryllium Alloy Forgings and ExtrusionB570Seamless Nickel and Nickel-Cobalt Alloy Pipe and TubeB622UNS N08028 Seamless TubesB668UNS N08904,UNS N08925 and UNS N08926 Seamless Pipeand TubeB677Iron-Nickel-Chromium-Molybdenum Alloys(UNS N08366 andUNS N08367)Seamless Pipe and TubeB690Ni-Cr-Mo-Co-W-Fe-Si Alloy(UNS N06333)Seamless Pipe andTubeB722Seamless UNS N08020,UNS N08026,and UNS N08024Nickel-Alloy Pipe and TubeB7291.2 One or more of the test requirements of Section 5 applyonly if specifically stated in the product specification or in thepurchase order.1.3 In case of conflict between a requirement of the productspecification and a requirement of this general specification,only the requirement of the product specification needs to besatisfied.1.4 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 The following safety hazards caveat pertains only to thetest requirements portion,Section 5,of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to become familiar with all hazards includingthose identified in the appropriate Safety Data Sheet(SDS)forthis product/material as provided by the manufacturer,toestablish appropriate safety and health practices,and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2B880 Specification for General Requirements for ChemicalCheck Analysis Limits for Nickel,Nickel Alloys andCobalt AlloysE8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE18 Test Methods for Rockwell Hardness of Metallic Ma-terialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE39 Methods for Chemical Analysis of Nickel(Withdrawn1995)3E76 Test Methods for Chemical Analysis of Nickel-CopperAlloys(Withdrawn 2003)31This specification is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.07 on Refined Nickel and Cobalt and Their Alloys.Current edition approved April 1,2017.Published April 2017.Originallyapproved in 1992.Last previous edition approved in 2009 as B829 04a(2009)1.DOI:10.1520/B0829-04AR17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 E112 Test Methods for Determining Average Grain SizeE213 Practice for Ultrasonic Testing of Metal Pipe andTubingE426 Practice for Electromagnetic(Eddy Current)Examina-tion of Seamless and Welded Tubular Products,Titanium,Austenitic Stainles