ASTM_B_210_-_B_210M_-_19.pdf

Designation:B210/B210M19Used in USNRC-NDT standardsStandard Specification forAluminum and Aluminum-Alloy Drawn Seamless Tubes1This standard is issued under the fixed designation B210/B210M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification2covers aluminum and aluminum-alloy drawn seamless tubes in straight lengths and coils forgeneral purpose and pressure applications in alloys(Note 2),tempers,and thicknesses shown in Table 2 Table 3.Coiledtubes are generally available only as round tubes with a wallthickness not exceeding 0.083 in.2.00 mm and only innon-heat-treatable alloys.1.2 Alloy and temper designations are in accordance withANSI H35.1/H35.1M.The equivalent Unified NumberingSystem alloy designations are those of Table 1 preceded byA9,for example,A91100 for aluminum designation 1100 in accor-dance with Practice E527.NOTE1See Specification B483/B483M for aluminum-alloy drawntubes for general purpose applications;Specification B234 for aluminum-alloy drawn seamless tubes for condensers and heat exchangers;andSpecification B241/B241M for aluminum-alloy seamless pipe and seam-less extruded tube.NOTE2Throughout this specification,use of the term alloy in thegeneral sense includes aluminum as well as aluminum alloy.1.3 For acceptance criteria for inclusion of new aluminumand aluminum alloys in this specification,see Annex A2.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 The following documents of the issue in effect on dateof material purchase form a part of this specification to theextent referenced herein:2.2 ASTM Standards:3B234 Specification for Aluminum and Aluminum-AlloyDrawnSeamlessTubesforSurfaceCondensers,Evaporators,and Heat ExchangersB241/B241M Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded TubeB483/B483M Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General PurposeApplicationsB557 Test Methods for Tension Testing Wrought and CastAluminum-and Magnesium-Alloy ProductsB557M Test Methods for Tension Testing Wrought and CastAluminum-and Magnesium-Alloy Products(Metric)B660 Practices for Packaging/Packing of Aluminum andMagnesium ProductsB666/B666M Practice for Identification Marking of Alumi-num and Magnesium ProductsB807/B807M Practice for Extrusion Press Solution HeatTreatment for Aluminum AlloysB881 Terminology Relating to Aluminum-and Magnesium-Alloy ProductsB918/B918M Practice for Heat Treatment of Wrought Alu-minum AlloysB985 Practice for Sampling Aluminum Ingots,Billets,Cast-ings and Finished or Semi-Finished Wrought AluminumProducts for Compositional AnalysisE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE215 Practice for Standardizing Equipment and Electromag-netic Examination of Seamless Aluminum-Alloy TubeE527 Practice for Numbering Metals and Alloys in theUnified Numbering System(UNS)1This specification is under the jurisdiction of ASTM Committee B07 on LightMetals and Alloys and is the direct responsibility of Subcommittee B07.03 onAluminum Alloy Wrought Products.Current edition approved Jan.1,2019.Published February 2019.Originallyapproved in 1946.Last previous edition approved in 2012 as B210 12.DOI:10.1520/B0210_B0210M-19.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SB-210 in Section II of that Code.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 E607 Test Method for Atomic Emission SpectrometricAnalysis Aluminum Alloys