ASTM_B_465_-_16.pdf

Designation:B46516Standard Specification forCopper-Iron Alloy Plate,Sheet,Strip,and Rolled Bar1This standard is issued under the fixed designation B465;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification establishes the requirements forcopper-iron alloy plate,sheet,strip,and rolled bar for CopperAlloy UNS Nos.C19200,C19210,C19400,C19500,C19700,and C19720.1.2 UnitsThe values stated in inch-pound units are to beregarded as standard.The values given in parentheses aremathematical conversions to SI units,which are provided forinformation only and are not considered standard.2.Referenced Documents2.1 ASTM Standards:2B193 Test Method for Resistivity of Electrical ConductorMaterialsB248 Specification for General Requirements for WroughtCopper and Copper-Alloy Plate,Sheet,Strip,and RolledBarB601 Classification for Temper Designations for Copper andCopper AlloysWrought and CastB846 Terminology for Copper and Copper AlloysE8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE54 Test Methods for Chemical Analysis of Special Brassesand Bronzes(Withdrawn 2002)3E62 Test Methods for Chemical Analysis of Copper andCopperAlloys(Photometric Methods)(Withdrawn 2010)3E75 Test Methods for Chemical Analysis of Copper-Nickeland Copper-Nickel-Zinc Alloys(Withdrawn 2010)3E112 Test Methods for Determining Average Grain SizeE478 Test Methods for Chemical Analysis of Copper Alloys3.General Requirements3.1 The following sections of Specification B248 constitutea part of this specification:3.1.1 Terminology3.1.2 Materials and Manufacture3.1.3 Workmanship,Finish,and Appearance3.1.4 Sampling3.1.5 Number of Tests and Retests3.1.6 Specimen Preparation3.1.7 Test Methods(except chemical analysis)3.1.8 Significance of Numerical Limits3.1.9 Inspection3.1.10 Rejection and Rehearing3.1.11 Certification3.1.12 Test Reports3.1.13 Packaging and Package Marking3.1.14 Supplementary Requirements.3.2 In addition,when a section with a title identical to thatreferenced in 3.1,above,appears in this specification,itcontains additional requirements which supplement those ap-pearing in Specification B248.4.Terminology4.1 For definitions of terms related to copper and copperalloys,refer to Terminology B846.5.Ordering Information5.1 Include the following specified choices when placingorders for product under this specification,as applicable:5.1.1 ASTM designation and year of issue,5.1.2 Copper Alloy UNS No.designation,5.1.3 Temper(Section 8),5.1.4 DimensionsThickness,width,length,and edges(Section 12),5.1.5 How FurnishedStraight lengths or coils,5.1.6 Quantitytotal weight or total length or number ofpieces of each size,and5.1.7 Intended application.5.2 The following options are available but may not beincluded unless specified at the time of placing of the orderwhen required:5.2.1 Heat identification or traceability details,1This specification is under the jurisdiction ofASTM Committee B05 on Copperand CopperAlloys and is the direct responsibility of Subcommittee B05.01 on Plate,Sheet,and Strip.Current edition approved Oct.1,2016.Published October 2016.Originallyapproved in 1968.Last previous edition approved in 2011 as B46511.DOI:10.1520/B0465-16.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.2.2 Certification,5.2.3 Test Report,5.2.4 Type of edge(slit,sheared,sawed,square corners,round corners,rounded edges,or full-rounded edges),5.2.5 Width and straightness tolerances(appropriate tablesin Specification B248),and5.2.6 If product is purchased for agencies of the U.S.Government(see the Supplemental section of SpecificationB248 for additional requirements,if specified).6.Materials and Manufacture6.1 Materials:6.1.1 The material of manufacture shall be a form(cast bar,cake,slab,et cetera),of Copper Alloy UNS No.C19200,C19210,C19400,C19500,C19700,or C19720 of such purityand soundness as to be suitable for processing into the productsprescribed herein.6.1.2 When specified in the contract or purchase order thatheat identification or traceability is required,the purchasershall specify the details desired.NOTE1Due to the discontinuous nature of the processing of castingsinto wrought products,it is not practical to identify a specific castinganalysis with a specific quanti