ASTM_B_435_-_06_2016.pdf

Designation:B43506(Reapproved 2016)Standard Specification forUNS N06002,UNS N06230,UNS N12160,and UNS R30556Plate,Sheet,and Strip1This standard is issued under the fixed designation B435;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification2covers alloys UNS N06002,UNSN06230,UNS N12160,and UNS R305563in the form ofrolled plate,sheet,and strip for heat-resisting and generalcorrosive service.1.2 The following products are covered under this specifi-cation:1.2.1 Sheet and StripHot-or cold-rolled,annealed,anddescaled unless solution annealing is performed in an atmo-sphere yielding a bright finish.1.2.2 PlateHot-rolled,solution-annealed,and descaled.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateSafety Data Sheet(SDS)for this product/material as providedby the manufacturer,to establish appropriate safety and healthpractices,and determine the applicability of regulatory limi-tations prior to use.2.Referenced Documents2.1 ASTM Standards:4B906 Specification for General Requirements for Flat-Rolled Nickel and Nickel Alloys Plate,Sheet,and StripE527 Practice for Numbering Metals and Alloys in theUnified Numbering System(UNS)3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 plate,nmaterial316in.(4.76 mm)and over inthickness.3.1.2 sheet and strip,nmaterial under316in.(4.76 mm)inthickness.4.General Requirements4.1 Material furnished under this specification shall con-form to the applicable requirements of Specification B906unless otherwise provided herein.5.Ordering Information5.1 It is the responsibility of the purchaser to specify allrequirements that are necessary for material ordered under thisspecification.Examples of such requirements include,but arenot limited to the following:5.1.1 Alloy,5.1.2 DimensionsThickness(in decimals of an inch),width,and length(inch or fraction of an inch),5.1.3 CertificationState if certification or a report of testresults is required(Specification B906,section on Material TestReport an Certification),5.1.4 Optional RequirementPlate;state how plate is to becut(Specification B906,Table titled Permissible Variations inwidth and Length of Sheared,Torch-Cut,or Abrasive-CutRectangular Plate),5.1.5 Purchase InspectionState which tests or inspectionsare to be witnessed(Specification B906,section on Inspection),and5.1.6 Samples for Product(Check)AnalysisState whethersamples should be furnished(Specification B906,section onSampling).6.Chemical Composition6.1 The material shall conform to the requirements as tochemical composition prescribed in Table 1.1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.07 on Refined Nickel and Cobalt and Their Alloys.Current edition approved June 1,2016.Published June 2016.Originallyapproved in 1966.Last previous edition approved in 2011 as B435 06(2011)1.DOI:10.1520/B0435-06R16.2For ASME Boiler and Pressure Vessel Code applications,see related Specifi-cation SB-435 in Section II of that Code.3New designation established in accordance with Practice E527 and SAE J1086,Practice for Numbering Metals and Alloys(UNS).4For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.2 If a product(check)analysis is made by the purchaser,the material shall conform to the requirements specified inTable 1 and Specification B906.7.Mechanical Properties and Other Requirements7.1 Tensile PropertiesThe material shall conform to theroom temperature tensile properties prescribed in Table 2.7.2 Grain Size for Sheet and Strip:7.2.1 Annealed alloys UNS N06002,UNS N06230,andUNS R30556 sheet and strip shall conform to the grain sizerequirements given in Table 3.7.2.2 Annealed alloy UNS N12160 shall conform to anaverage grain size of ASTM No.5 or coarser.8.Dimensions,Mass,and Permissible Variations8.1 WeightFor calculations of mass or weight,the follow-ing densities shall be used:AlloyDensitylb/in.3(g/cm3)N060020.297(8.23)N062300.324(8.97)R305560.297(8.23)N121600.292(8.08)8.2 Thickness:8.2.1 Sheet and StripThe thickness shall be m