ASTM_A_524_-_17.pdf

Designation:A52417Standard Specification forSeamless Carbon Steel Pipe for Atmospheric and LowerTemperatures1This standard is issued under the fixed designation A524;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification2covers seamless carbon steel pipeintended primarily for service at atmospheric and lowertemperatures,NPS18to 26 inclusive,with nominal(average)wall thickness as given in ANSI B36.10.Pipe having otherdimensions may be furnished,provided such pipe complieswith all other requirements of this specification.Pipe orderedto this specification shall be suitable both for welding,and forbending,flanging,and similar forming operations.1.2 The product is available in two grades(Tables 1 and 2).1.3 Product may be either of hot finished or cold drawnmanufacture(see 5.1.4 and 5.1.5).1.4 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.NOTE1The dimensionless designator NPS(nominal pipe size)hasbeen substituted in this standard for such traditional terms as“nominaldiameter,”“size,”and“nominal size.”1.5 The following hazard caveat applies to the test methodsportion,Section 16,only.This standard does not purport toaddress all of the safety concerns,if any,associated with itsuse.It is the responsibility of the user of this standard toestablish appropriate safety,health,and environmental prac-tices and determine the applicability of regulatory limitationsprior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3A530/A530M Specification for General Requirements forSpecialized Carbon and Alloy Steel PipeE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with Specifications2.2 American National Standards Institute Standard:B36.10 Welded and Seamless Wrought Steel Pipe43.Ordering Information3.1 Orders for material under this specification shouldinclude the following,as required,to describe the desiredmaterial adequately:3.1.1 Quantity(feet or number of lengths),3.1.2 Name of material(seamless carbon steel pipe),3.1.3 Grade(Table 1 and Table 2),3.1.4 Manufacture(hot finished or cold drawn(see 5.1.4 and5.1.5),3.1.5 Size(either nominal wall thickness and weight class orschedule number,or both,or outside diameter and nominalwall thickness,ANSI B36.10),3.1.6 Length(Section 17),3.1.7 Optional requirements(Section 8 and Section 11 ofSpecification A530/A530M),3.1.8 Test report required(Certification Section of Specifi-cation A530/A530M),3.1.9 Specification designation,3.1.10 Hydrostatic test(see 11.2).3.1.11 End use of material,and3.1.12 Special requirements.4.General Requirements4.1 Material furnished to this specification shall conform tothe applicable requirements of the current edition of Specifi-cation A530/A530M unless otherwise provided herein.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.09 on Carbon Steel Tubular Products.Current edition approved Nov.1,2017.Published November 2017.Originallyapproved in 1965.Last previous edition approved in 2012 as A524 96(2012).DOI:10.1520/A0524-17.2For ASME Boiler and Pressure Vessel Code Applications see related Specifi-cation SA-524 in Section II of that Code.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Available from American National Standards Institute,11 West 42nd St.,13thFloor,New York,NY 10036.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 5.Materials and Manufacture5.1 Process:5.1.1 The steel shall be killed steel made by one or more ofthe following processes:open-hearth,electric-furnace,orbasic-oxygen.5.1.2 The steel shall be made to fine grain practice.5.1.3 Steel may be c