分享
ASTM_A_263_-_12_2019.pdf
下载文档

ID:186624

大小:172.30KB

页数:6页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_A_263_ _12_2019
Designation:A26312(Reapproved 2019)Standard Specification forStainless Chromium Steel-Clad Plate1This standard is issued under the fixed designation A263;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification2covers plate of a carbon steel orlow-alloy steel base to which is integrally and continuouslybonded on one or both sides a layer of stainless chromiumsteel.The material is generally intended for pressure vesseluse.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3A6/A6M Specification for General Requirements for RolledStructural Steel Bars,Plates,Shapes,and Sheet PilingA20/A20M Specification for General Requirements for SteelPlates for Pressure VesselsA240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate,Sheet,and Strip for PressureVessels and for General ApplicationsA370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA480/A480M Specification for General Requirements forFlat-Rolled Stainless and Heat-Resisting Steel Plate,Sheet,and StripA578/A578M Specification for Straight-Beam UltrasonicExamination of Rolled Steel Plates for Special Applica-tionsA751 Test Methods,Practices,and Terminology for Chemi-cal Analysis of Steel Products2.2 Other Standards:ASME Boiler and Pressure Vessel Code,Section IX43.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 This material is considered as single-clad or double-clad stainless chromium-steel plate,depending on whether oneor both sides are covered.3.1.2 alloy cladding,nthe stainless chromium steel com-ponent of the composite plate.3.1.3 base metal(backing steel),ncomponent to whichthe alloy cladding is applied,usually the greater percentage ofthe composite plate.3.1.4 integrally and continuously bonded,na condition inwhich the alloy cladding and base metal are brought together toform a metallurgical bond at essentially the entire interface ofthe two metals by means other than those processes that do notproduce a homogeneous composite plate.4.Ordering Information4.1 It is the responsibility of the purchaser to specify allrequirements that are necessary for material ordered under thisspecification.Such requirements may include,but are notlimited to,the following:4.1.1 Quantity(weight or number of pieces).4.1.2 Cladding alloy specification(UNS or ASTM Specifi-cation A240/A240M)and whether cladding is for corrosionallowance only.4.1.3 Base metal specification.4.1.4 Bond integrity Class(1,3,or 5;see Section 13).4.1.5 Dimensions including the minimum or nominal thick-nesses of the cladding alloy and the backing steel,or of thetotal composite and if more or less restrictive thicknesstolerances apply.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.11 for Steel Plates for Boilers and Pressure Vessels.Current edition approved March 1,2019.Published April 2019.Originallyapproved in 1943.Last previous edition approved in 2012 as A263 12.DOI:10.1520/A0263-12R19.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SA-263 in Section II of that Code.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Available from American Society of Mechanical Engineers(ASME),ASMEInternational Headquarters,Two Park Ave.,New York,NY 10016-5990,http:/www.asme.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 4.1.6 Product analysis,if required(see Section 10).Specifywhether applicable to the cladding alloy,backing steel,or both.4.1.7 Mechanical properties including shear test if re

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开