ASTM_C_110_-_16e1.pdf

Designation:C110161Standard Test Methods forPhysical Testing of Quicklime,Hydrated Lime,andLimestone1This standard is issued under the fixed designation C110;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1NOTEAdded research report footnote to Section 24 editorially in January 2017.1.Scope1.1 These test methods cover physical testing of quicklimeand hydrated lime,and of limestone not otherwise covered inASTM standards.2NOTE1Quicklime and hydrated lime have a high affinity for moistureand carbon dioxide.Caution should be taken to protect both hydrated andquicklime during sampling,storage,and testing(see Practice C50).1.2 The test procedures appear in the following order:Plastic Property TestingSectionStandard Consistency of Lime Putty5Plasticity of Lime Putty6Water Retention of Hydrated Lime7Air Entrainment8Soundness TestingAutoclave Expansion of Hydrated and Hydraulic Lime9Popping and Pitting of Hydrated Lime10Application TestingSlaking Rate of Quicklime11Dry Brightness of Pulverized Limestone12Limestone Grindability Determination by the Laboratory Ball MillMethod13Settling Rate of Hydrated Lime14Particle Size AnalysisResidue and Sieve Analysis15Sieve Analysis of Dry Limestone,Quicklime,and Hydrated Lime16Fineness of Pulverized Quicklime and Hydrated Lime by AirPermeabiity17Particle Size of Pulverized Limestone18Dry Screening of Hydrated Lime,Pulverized Quicklime,andLimestone by Air Jet Sieving19Wet Sieve Analysis of Agricultural Liming Materials20Density MeasurementApparent Loose Density of Hydrated Lime,Pulverized Quicklime,and Limestone21Apparent Packed Density of Hydrated Lime,PulverizedQuicklime,and Limestone22Relative Density(Specific Gravity)of Hydrated Lime Products231.3 The values stated in SI units are to be regarded asstandard.The values given in brackets are mathematicalconversions to inch-pound units that are provided for informa-tion only and are not considered standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:3C28/C28M Specification for Gypsum PlastersC50 Practice for Sampling,Sample Preparation,Packaging,and Marking of Lime and Limestone ProductsC51 Terminology Relating to Lime and Limestone(as usedby the Industry)C91 Specification for Masonry CementC109/C109M Test Method for Compressive Strength ofHydraulic Cement Mortars(Using 2-in.or 50-mm CubeSpecimens)C136 Test Method for Sieve Analysis of Fine and CoarseAggregatesC150 Specification for Portland CementC185 Test Method for Air Content of Hydraulic CementMortarC188 Test Method for Density of Hydraulic CementC192/C192M Practice for Making and Curing Concrete TestSpecimens in the LaboratoryC204 Test Methods for Fineness of Hydraulic Cement byAir-Permeability ApparatusC207 Specification for Hydrated Lime for Masonry Pur-posesC230/C230M Specification for Flow Table for Use in Tests1These test methods are under the jurisdiction of ASTM Committee C07 onLime and Limestone and are the direct responsibility of Subcommittee C07.06 onPhysical Tests.Current edition approved Dec.1,2016.Published January 2017.Originallyapproved in 1934.Last previous edition approved in 2016 as C110 16.DOI:10.1520/C0110-16E01.2For tests on limestone as aggregate,see Vol 04.02 of the Annual Book of ASTMStandards.For tests on limestone as building stone,see Vol 04.05 of the AnnualBook of ASTM Standards.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 of Hydraulic CementC231 Test Method for Air Content of Freshly Mixed Con-crete by the Pressure MethodC305 Practice for Mechanical Mixing of Hydraulic CementPastes and Mortars of Plastic ConsistencyC430 Test Method for Fineness of Hydraulic Cement by the45-m(No.325)SieveC472 Test Methods for Physical Testing of Gypsum,Gyp-sum Plasters and Gypsum ConcreteC595 Specification for Blended Hydraulic CementsC670 Practice for Preparing