ASTM_B_514_-_05_2014.pdf

Designation:B51405(Reapproved 2014)Standard Specification forWelded Nickel-Iron-Chromium Alloy Pipe1This standard is issued under the fixed designation B514;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification2covers nickel-iron-chromium alloysin the form of welded,cold-worked,and annealed pipe forgeneral corrosive service and heat-resisting applications.Theseproducts are furnished in three alloys:UNS N08120,UNSN08800,and UNS N08810.3Alloy UNS N08800 is employednormally in service temperatures up to and including 1100F(593C).Alloys UNS N08120 and UNS N08810 are employednormally in service temperatures above 1100F where resis-tance to creep and rupture is required,and are annealed todevelop controlled grain size for optimum properties in thistemperature range.1.2 This specification covers outside diameter and nominalwall pipe shown in ANSI B36.19.Pipe having other dimen-sions may be furnished provided such pipe complies with allother requirements of the specification.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet(MSDS)for this product/materialas provided by the manufacturer,to establish appropriatesafety and health practices,and determine the applicability ofregulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:4B775 Specification for General Requirements for Nickel andNickel Alloy Welded PipeB899 Terminology Relating to Non-ferrous Metals and Al-loys2.2 ANSI Standard:B36.19 Stainless Steel Pipe53.Terminology3.1 Terms defined in Terminology B899 shall apply unlessdefined otherwise in this standard.4.General Requirement4.1 Material furnished in accordance with this specificationshall conform to the applicable requirements of the currentedition of Specification B775 unless otherwise providedherein.5.Ordering Information5.1 Orders for material under this specification shouldinclude the following information:5.1.1 Alloy name or UNS number.5.1.2 ASTM designation and year of issue.5.1.3 Condition(temper)(Table 1).5.1.4 Dimensions:5.1.4.1 Nominal pipe size or outside diameter and schedulenumber or nominal wall thickness.5.1.4.2 Length(specific or random).5.1.5 Quantity(feet or metres,or number of pieces).5.1.6 CertificationState if certification or a report of testresults is required.1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.07 on Refined Nickel and Cobalt and Their Alloys.Current edition approved Oct.1,2014.Published October 2014.Originallyapproved in 1970.Last previous edition approved in 2009 as B514 05(2009).DOI:10.1520/B0514-05R14.2For ASME Boiler and Pressure Code applications see related SpecificationSB-514 in Section II of that Code.3New designation established in accordance with ASTM E527 and SAE J1086,Practice for Numbering Metals and Alloys(UNS).4For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.5Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.1.7 Samples for Product(Check)AnalysisState whethersamples for product(check)analysis should be furnished.5.1.8 Purchaser InspectionIf the purchaser wishes towitness tests or inspection of material at the place ofmanufacture,the purchase order must so state indicating whichtests or inspections are to be witnessed.6.Materials and Manufacture6.1 Pipe shall be made from flat-rolled alloy by an auto-matic welding process with no addition of filler metal.Subse-quent to welding and prior to final solution treatment,thematerial shall be cold worked either in both weld and basemetal or in weld metal only.6.2 Pipe shall be furnished with a scale-free finish.Whenbright annealing is used,descaling is not necessary.7.Chemical Composition7.1 The material shall conform to the requirements as tochemical composition prescribed in Table 2.7.2 If a product(check)analysis is performed by thepurchaser,the material shall conform to the product(check)analysis variations in Table 1 of Specification B775.8.Mechan