ASTM_B_150_-_B_150M_-_12_2017.pdf

Designation:B150/B150M12(Reapproved 2017)Standard Specification forAluminum Bronze Rod,Bar,and Shapes1This standard is issued under the fixed designation B150/B150M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification establishes the requirements for alu-minum bronze rod,bar,and shapes for Copper Alloys UNSNos.C61300,C61400,C61900,C62300,C62400,C63000,C63020,C63200,C64200,and C64210.NOTE1Product intended for hot forging is described in SpecificationB124/B124M.NOTE2WarningMercury has been designated by many regulatoryagencies as a hazardous material that can cause serious medical issues.Mercury,or its vapor,has been demonstrated to be hazardous to health andcorrosive to materials.Caution should be taken when handling mercuryand mercury containing products.See the applicable product Safety DataSheet(SDS)for additional information.Users should be aware that sellingmercury and/or mercury containing products into your state or countrymay be prohibited by law.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory requirements prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2B124/B124M Specification for Copper and Copper AlloyForging Rod,Bar,and ShapesB154 Test Method for Mercurous Nitrate Test for CopperAlloysB249/B249M Specification for General Requirements forWrought Copper and Copper-Alloy Rod,Bar,Shapes andForgingsB601 Classification for Temper Designations for Copper andCopper AlloysWrought and CastB858 Test Method forAmmonia Vapor Test for DeterminingSusceptibility to Stress Corrosion Cracking in CopperAlloysE8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE18 Test Methods for Rockwell Hardness of Metallic Ma-terialsE53 Test Method for Determination of Copper in UnalloyedCopper by GravimetryE62 Test Methods for Chemical Analysis of Copper andCopperAlloys(Photometric Methods)(Withdrawn 2010)3E118 Test Methods for Chemical Analysis of Copper-Chromium Alloys(Withdrawn 2010)3E478 Test Methods for Chemical Analysis of Copper Alloys3.General Requirements3.1 The following sections of Specification B249/B249Mconstitute a part of this specification:3.1.1 Terminology,3.1.2 Materials and Manufacture,3.1.3 Workmanship,Finish,and Appearance,3.1.4 Sampling,3.1.5 Number of Tests and Retests,3.1.6 Specimen Preparation,3.1.7 Test Methods,3.1.8 Significance of Numerical Limits,3.1.9 Inspection,3.1.10 Rejection and Rehearing,3.1.11 Certification,3.1.12 Mill Test Report,3.1.13 Packaging and Package Marking,Preservation andDelivery,and1This specification is under the jurisdiction ofASTM Committee B05 on Copperand Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod,Bar,Wire,Shapes and Forgings.Current edition approved April 1,2017.Published April 2017.Originallyapproved in 1941.Last previous edition approved in 2012 as B150/B150M-12.DOI:10.1520/B0150_B0150M-12R17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.1.14 Supplementary Requirements.3.2 In addition,when a section with a title identical to thosereferenced in 3.1,appears in this specification,it containsadditional requirements that supplement those appearing inSpecification B249/B249M.4.Ordering Infor