分享
ASTM_A_886_-_A_886M_-_17.pdf
下载文档

ID:186076

大小:96.15KB

页数:4页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_A_886_ _A_886M_ _17
Designation:A886/A886M17Standard Specification forSteel Strand,Indented,Seven-Wire Stress-Relieved forPrestressed Concrete1This standard is issued under the fixed designation A886/A886M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers two types and two grades ofindented seven-wire uncoated,steel strand for use in pre-stressed concrete construction.The two types of strand arelow-relaxation and stress-relieved(normal-relaxation).Grade250I 1725I and Grade 270I 1860I have minimum tensilestrengths of 250 ksi 1725 MPa and 270 ksi 1860 MPa,respectively,based on the nominal area of the strand.1.2 This specification is applicable for orders in eitherinch-pound units(as Specification A886)or in SI units(asSpecification A886M).1.3 The values stated in either inch-pound units or SI unitsare to be regarded separately as standard.Within the text,theSI units are shown in brackets.The values stated in eachsystem are not exact equivalents;therefore,each system shallbe used independently of the other.Combining values from thetwo systems may result in non-conformance with the specifi-cation.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standard:2A1061/A1061M Test Methods for Testing Multi-Wire SteelPrestressing Strand2.2 U.S.Military Standard:MIL-STD-129 Marking for Shipment and Storage32.3 U.S.Federal Standard:Fed.Std.No.123 Marking for Shipments(Civil Agencies)33.Terminology3.1 Definition of Term Specific to this Specification:3.1.1 strand,na group of wires having a center wireenclosed tightly by six helically placed outer wires withuniform pitch of not less than 12 and not more than 16 timesthe nominal diameter of the strand.3.1.1.1 DiscussionThe direction of lay is either right-handed or left-handed.4.Ordering Information4.1 Orders for indented seven-wire steel strand under thisspecification shall contain the following information:4.1.1 Quantity(feet metres),4.1.2 Nominal diameter of strand(inches millimetres),4.1.3 Grade of strand,4.1.4 Type of strand(low-relaxation or stress-relieved(normal-relaxation),and4.1.5 ASTM designation A886 A886M and year of issue.4.2 The purchaser shall have the option to specify additionalrequirements,including but not limited to,the following:4.2.1 Relaxation evidence from similarly dimensionedstrand of the same grade(6.5.1),4.2.2 Other types of indented wire(7.4.2),4.2.3 If joints or splices are permitted(8.1.1),4.2.4 Weldless,if desired(8.1.4),4.2.5 Requirements for inspection(11.1),4.2.6 Load-elongation curve,if desired(13.2),4.2.7 Packaging and package marking(Section 14),and4.2.8 Other special requirements,if any.5.Materials and Manufacture5.1 Base MetalThe base metal shall be carbon steel ofsuch quality that when it is drawn to wire,subjected to the1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.05 on Steel Reinforcement.Current edition approved Nov.1,2017.Published November 2017.Originallyapproved in 1988.Last previous edition approved in 2016 as A886/A886M 16.DOI:10.1520/A0886_A0886M-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from U.S.Government Printing Office,Superintendent ofDocuments,732 N.Capitol St.,NW,Washington,DC 20401-0001,http:/www.access.gpo.gov.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 indentation process,fabricated into strand,and then thermallytreated,it shall have the properties and characteristics pre-scribed in this specification.5.2 WireThe wire from which the strand is to be fabricatedshall have a common dry-drawn finish.NOTE1This product is a composite of seven wires and is produced toonly the prescribed mechanical properties.The chemical composition ofall wires or any individual wire is not pertinent to this application,andheat iden

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开