ASTM_A_849_-_15.pdf

Designation:A84915Standard Specification forPost-Applied Coatings,Pavings,and Linings for CorrugatedSteel Sewer and Drainage Pipe1This standard is issued under the fixed designation A849;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers post-applied coatings,pavings,and linings for corrugated steel pipe and corrugated steelstructural plate pipe,pipe-arches,and arches coated,paved,orlined with specified materials over either metallic coatings ormetallic coatings with polymer coatings.This specificationincludes asphalt,polymerized asphalt,polymer,mastic,andemulsion coatings and asphalt and concrete pavements andlinings applied to the pipe in the producing plant,as well as,asphalt and mastic coatings applied in the field.Field-appliedconcrete pavements and linings are covered by SpecificationA979/A979M.The pipe to which the coatings are applied isdescribed in Specifications A760/A760M,A761/A761M,andA762/A762M.1.2 There is no cleaning operation currently included in pipecoating practice.However,experience has shown that a cleansubstrate provides good adherence for both cold-and hot-applied post coatings.The performance of post coating orlining,or both,will depend on the surface cleanliness overwhich it is applied.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in brackets are for informationonly.1.4 The following safety hazards caveat pertains only to thetest methods portions,Sections 11 and 12,of this specification.This standard does not purport to address all of the safetyconcerns,if any,associated with its use.It is the responsibilityof the user of this standard to establish appropriate safety andhealth practices and determine the applicability of regulatorylimitations prior to use.2.Referenced Documents2.1 ASTM Standards:2A185/A185M SpecificationforSteelWeldedWireReinforcement,Plain,for Concrete(Withdrawn 2013)3A615/A615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete ReinforcementA742/A742M Specification for Steel Sheet,Metallic Coatedand Polymer Precoated for Corrugated Steel PipeA760/A760M Specification for Corrugated Steel Pipe,Metallic-Coated for Sewers and DrainsA761/A761M Specification for Corrugated Steel StructuralPlate,Zinc-Coated,for Field-Bolted Pipe,Pipe-Arches,and ArchesA762/A762M Specification for Corrugated Steel Pipe,Poly-mer Precoated for Sewers and DrainsA862/A862M Practice for Application of Asphalt Coatingsto Corrugated Steel Sewer and Drainage PipeA926 Test Method for Comparing the Abrasion Resistanceof Coating Materials for Corrugated Metal PipeA979/A979M Specification for Concrete Pavements andLinings Installed in Corrugated Steel Structures in theFieldC31/C31M Practice for Making and Curing Concrete TestSpecimens in the FieldC33 Specification for Concrete AggregatesC39/C39M Test Method for Compressive Strength of Cylin-drical Concrete SpecimensC150 Specification for Portland CementC309 Specification for Liquid Membrane-Forming Com-pounds for Curing ConcreteC595 Specification for Blended Hydraulic Cements1This specification is under the jurisdiction of ASTM Committee A05 onMetallic-Coated Iron and Steel Products and is the direct responsibility ofSubcommittee A05.17 on Corrugated Steel Pipe Specifications.Current edition approved May 1,2015.Published May 2015.Originallyapproved in 1985.Last previous edition approved in 2010 as A849-10.DOI:10.1520/A0849-15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 C618 Specification for Coal Fly Ash and Raw or CalcinedNatural Pozzolan for Use in ConcreteC670 Practice for Preparing Precision and Bias Statementsfor Test Methods for Construction MaterialsD5 Test Method for Penetration of Bituminous MaterialsD6 Test Method for Loss on Heating of Oil and AsphalticCompoundsD36 Test Method for Softening Point of Bitumen(Ring-and-Ball Apparatus)D70 Test Method for Density of Semi-Solid BituminousMaterials(Pycnometer Method)D92 Test Method for Flash and Fire Points by ClevelandOpen Cup TesterD1005 Test Method for Measurement of Dry-Film Thick-ness of Organic Coatings Using MicrometersD1187 Specification for Asphalt-Base Emulsions for Use asProtective Coatings for MetalD2042 Test Method for Solubility of Asphalt Materials inTrichloroethyleneD4402 Test Method for Viscosity Determinat