分享
ASTM_D_1061_-_D_1061M_-_95_2017.pdf
下载文档

ID:185812

大小:93.02KB

页数:4页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_1061_ _D_1061M_ _95_2017
Designation:D1061/D1061M95(Reapproved 2017)Standard Specification forAsbestos Lap1This standard is issued under the fixed designation D1061/D1061M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers asbestos lap,a felted asbestosproduct,having a minimum of 75 mass%of asbestos fiber.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 WarningBreathing of asbestos dust is hazardous.Asbestos and asbestos products present demonstrated healthrisks for users and for those with whom they come into contact.In addition to other precautions,when working with asbestos-cement products,minimize the dust that results.For informa-tion on the safe use of chrysoltile asbestos,refer to“Safe Useof Chrysotile Asbestos:A Manual on Preventive and ControlMeasures.”21.4 The following safety hazards caveat pertains only to thetest methods,Section 12,described in this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.For specific safety hazard,see 1.3.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D123 Terminology Relating to TextilesD1118 Test Method for Magnetic Rating of Asbestos Fiberand Asbestos TextilesD1918 Test Method for Asbestos Content of Asbestos Tex-tilesD2946 Terminology for Asbestos and AsbestosCementProducts3.Terminology3.1 For definitions of other textile terms used in thisspecification refer to Terminology D123.For asbestos termsrefer to Terminology D2946.3.2 Definitions:3.2.1 asbestosa group of impure silicate minerals occur-ring in fibrous form.3.2.2 asbestos fiberthe hydrous magnesium silicate ser-pentine mineral designated as chrysotile and having the em-pirical formula Mg3Si2O5(OH)4.3.2.3 atmosphere for testing textilesfor asbestos,air main-tained at a relative humidity of 50 6 2%at 21 6 1C.3.2.4 lap,nfor asbestos,a flat compressed form of cardedor otherwise felted asbestos fiber,with or without carrier fibers.3.2.5 magnetic rating(MR)an empirical value that reflectsthe effect of magnetic particles,such as magnetic ironcompounds,in asbestos material as measured by a magneticanalyzer.NOTE1Magnetic rating is not a quantitative measure of the number ormass of magnetic particles in the material.4.Classifications4.1 StylesThe style of asbestos lap refers to the physicalconstruction.Two styles are available:1This specification is under the jurisdiction of ASTM Committee C17 onFiber-Reinforced Cement Products and is the direct responsibility of SubcommitteeC17.03 on Asbestos-Cement Sheet Products and Accessories.Current edition approved June 1,2017.Published July 2017.Originally approvedin 1949.Last previous edition approved in 2009 as D1061/D1061M 95(2009)1.DOI:10.1520/D1061_D1061M-95R17.2Available from The Asbestos Institute,http:/ referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 4.1.1 Style 1A single compressed flat formation of cardedor otherwise felted asbestos fibers,and4.1.2 Style 2A flat parallel assemblage of compressedcarded asbestos slivers.4.2 GradesThe grades of asbestos lap are based on themass percentage of asbestos content as stated in Table 1.4.3 Mass per Unit LengthAsbestos lap is normally fur-nished in the following nominal linear densities:g/mlb/100 yd204501070141002015030Other linear densities may be furnished as agreed uponbetween the purchaser and the seller.4.4 Types:4.4.1 Asbestos lap as made for the electrical industry isfurnis

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开