ASTM_C_1449_-_C_1449M_-_05a_2014.pdf

Designation:C1449/C1449M05a(Reapproved 2014)Standard Specification forNon-Asbestos Fiber-Cement Nonpressure Sewer Pipe1This standard is issued under the fixed designation C1449/C1449M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers requirements relating to non-asbestos fiber-cement non-pressure sewer pipe,joints,andfittings suitable for use with gravity flow,intended for sewer-age and drainage applications from point of use to point oftreatment or disposal.It defines certain conditions ofmanufacture,classification,characteristics,and acceptancetests applicable to these products.1.2 The values stated in either inch-pound units or SI unitsare to be regarded separately as standard.Within the text,theSI units are shown in brackets.The values stated in eachsystem are not exact equivalents;therefore each system shallbe used independently of the other.Combining values from thetwo systems may result in nonconformance with the specifi-cation.NOTE1Rubber rings suitable for use with this pipe are covered inSpecification D1869.NOTE2This specification is issued for product standardization andpurchasing purposes only,and does not include requirements for instal-lation or the relationships between operating conditions and the strengthcharacteristics of the various classifications of pipe.The purchaser iscautioned that he must correlate installation and operating conditions withthe specified characteristics of the pipe.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2C150 Specification for Portland CementC497 Test Methods for Concrete Pipe,Manhole Sections,orTileC500 Test Methods for Asbestos-Cement PipeC595 Specification for Blended Hydraulic CementsC1154 Terminology for Non-Asbestos Fiber-Reinforced Ce-ment ProductsD1869 Specification for Rubber Rings for Asbestos-CementPipe2.2 Federal Standard:No.123 Marking for Domestic Shipment(Civilian Agen-cies)32.3 Military Standard:No.129 Marking for Shipment and Storage32.4 ISO Standards:ISO 390:1993 Products in Fibre Reinforced CementSampling and Inspection4ISO 2859-1:1999 Sampling Procedures for Inspection byAttributes Part 1:Sampling Schemes Indexed by Accep-tance Quality Limit(AQL)for Lot-by-Lot Inspection4ISO 3951:1989 Sampling Procedures and Charts for Inspec-tion by Variables for Percent Nonconforming42.5 Other Standards:Uniform Freight Classification Rules5National Motor Freight Classification Rules63.Terminology3.1 Definitions:3.1.1 Refer to Terminology C1154.3.1.2 couplingsection for joining fiber-cement non-pressure sewer pipe,as defined in 5.3,that when properlyinstalled with the proper accessories,develops an assembledjoint,equivalent in serviceability and strength to the pipesections when tested in accordance with 6.3.3.1.3 fittingcomponents such as wyes,tees,adaptors,foruse in laying fiber-cement pipe,such that,when properlyinstalled,yields develops an assembly fitting equivalent inserviceability and strength to the pipe sections.1This specification is under the jurisdiction of ASTM Committee C17 onFiber-Reinforced Cement Products and is the direct responsibility of Subcommit-tee C17.02 on Non-Asbestos Fiber Cement Products.Current edition approved Dec.1,2014.Published December 2014.Originallyapproved in 1999.Last previous edition approved in 2010 as C1449/C1449M 05a(2010).DOI:10.1520/C1449_C1449M-05AR14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk,Bldg.4 Section D,700Robbins Ave.,Philadelphia,PA 19111-5094,Attn:NPODS.4Available from International Organization for Standardization(ISO),1 rue deVaremb,Case postale 56,CH-1211,Geneva 20,Switzerland.5Available from the Uniform Classification Commission,Room 1106,222 S.Riverside Plaza,Chicago,IL 60606.6Available from National Motor Freight Inc.,1616 P St.,NW,Washington,DC20036.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.1.4 pipefiber-cement non-pressure sewer pipe as definedin Sections 1,3,and 5.4.Classification4.1 The types of pipe shall be shown as Type I and Type IIcorresponding to the chemical requirements given in S3.NOTE3There are no chemical requirements for Type I pipe.Type IIpipe is generally accepted as being unaffected by sulfates in groundwaterwhich cause mat