ASTM_D_1048_-_22.pdf

Designation:D104822Standard Specification forRubber Insulating Blankets1This standard is issued under the fixed designation D1048;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers acceptance testing of rubberinsulating blankets for protection of workers from accidentalcontact with live electrical conductors,apparatus,or circuits.1.2 Two types of blankets are provided and are designatedas Type I,not resistant to ozone,and Type II,resistant to ozone.1.3 Five classes of blankets,differing in electricalcharacteristics,are provided and are designated as Class 0,Class 1,Class 2,Class 3,and Class 4.1.4 Two styles of blankets,differing in constructioncharacteristics,are provided and are designated as Style A andStyle B.1.5 The values stated in SI units are to be regarded asstandard.The values given in parentheses after SI units areprovided for information only and are not considered standard.1.6 The following safety hazards caveat pertains only to thetest method portion,Sections 16 19,of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety,health,andenvironmental practices and determine the applicability ofregulatory limitations prior to use.1.7 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D149 Test Method for Dielectric Breakdown Voltage andDielectric Strength of Solid Electrical Insulating Materialsat Commercial Power FrequenciesD297 Test Methods for Rubber ProductsChemical Analy-sisD412 Test Methods for Vulcanized Rubber and Thermoplas-tic ElastomersTensionD518 Test Method for Rubber DeteriorationSurfaceCracking(Withdrawn 2007)3D570 Test Method for Water Absorption of PlasticsD573 Test Method for RubberDeterioration in an AirOvenD624 Test Method for Tear Strength of Conventional Vul-canized Rubber and Thermoplastic ElastomersD1388 Test Method for Stiffness of FabricsD2865 Practice for Calibration of Standards and Equipmentfor Electrical Insulating Materials TestingF819 Terminology Relating to Electrical Protective Equip-ment for Workers2.2 American National Standards:ANSI/IEEE C 2 National Electrical Safety Code4C84.1 Electric Power Systems and EquipmentVoltageRatings(60 Hz)53.Terminology3.1 Definitions:3.1.1 beaded edge,na narrow border of thicker rubberwhich extends completely around the outer edges of theblanket.1This specification is under the jurisdiction of ASTM Committee F18 onElectrical Protective Equipment for Workers and is the direct responsibility ofSubcommittee F18.25 on Insulating Cover-Up Equipment.This standard replacesANSI Standard J 6.4,which is no longer available.Current edition approved July 1,2022.Published August 2022.Originallyapproved in 1949 as D1048 49 T.Last previous edition approved in 2020 asD1048-20.DOI:10.1520/D1048-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from Institute of Electrical and Electronics Engineers,Inc.(IEEE),445 Hoes Ln.,P.O.Box 1331,Piscataway,NJ 08854-1331,http:/www.ieee.org.5Available from National Electrical Manufacturers Association(NEMA),1300N.17th St.,Suite 900,Arlington,VA 22209,http:/www.nema.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.13.1.2 breakdown,nthe electrical discharge or arc occur-ring between the electrodes and through the equipment beingtested.3.1.3 designated person,nan individual who is qualifiedby experience or training to perform an assigned task.3.1.4 electrical testing facility,na location with qualifiedpersonnel,testing equipment,and procedures for the inspectionand electrical testing of electrical insulating protective equip-ment.3.1.5 electrode clearancethe shortest