分享
ASTM_C_795_-_08_2018.pdf
下载文档

ID:185527

大小:123.60KB

页数:4页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_C_795_ _08_2018
Designation:C79508(Reapproved 2018)Standard Specification forThermal Insulation for Use in Contact with AusteniticStainless Steel1This standard is issued under the fixed designation C795;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers non-metallic thermal insula-tion for use in contact with austenitic stainless steel piping andequipment.In addition to meeting the requirements specified intheir individual material specifications,issued under the juris-diction of ASTM Committee C16,these insulations must passthe preproduction test requirements of Test Method C692,forstress corrosion effects on austenitic stainless steel,and theconfirming quality control,chemical requirements,when testedin accordance with the Test Methods C871.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C168 Terminology Relating to Thermal InsulationC390 Practice for Sampling and Acceptance of ThermalInsulation LotsC692 Test Method for Evaluating the Influence of ThermalInsulations on External Stress Corrosion Cracking Ten-dency of Austenitic Stainless SteelC871 Test Methods for Chemical Analysis of Thermal Insu-lation Materials for Leachable Chloride,Fluoride,Silicate,and Sodium Ions3.Terminology3.1 DefinitionsTerminology C168 applies to the termsused in this specification.3.2 Definitions of Terms Specific to This Standard:3.2.1 basic material specificationany of the materialspecifications for homogeneous insulation covered in any ofthe pertinent Annual Book of ASTM Standards.3.2.2 lota lot shall be defined in accordance with PracticeC390 by agreement between the purchaser and the manufac-turer.3.2.3 stress corrosion cracking(SCC)the failure of metal,taking the form of cracks that potentially occur under thecombined influence of certain corrosive environments andapplied or residual stresses.3.2.4 wicking-type insulationinsulation material that,byvirtue of its physical characteristics,permits a wetting liquid toinfiltrate it by capillary attraction.4.Significance and Use4.1 Stress corrosion cracking of austenitic stainless steel is ametallurgical phenomenon.One cause of stress corrosioncracking is the presence of contaminants in water solution,which can be concentrated at the stressed surface by evapora-tion of the water.4.2 There is an apparent correlation between stress corro-sion cracking of austenitic stainless steel and the use ofinsulation which either contains water-leachable chloride or,byreason of its water absorptivity,acts as a vehicle through which1This specification is under the jurisdiction of ASTM Committee C16 onThermal Insulation and is the direct responsibility of Subcommittee C16.20 onHomogeneous Inorganic Thermal Insulations.Current edition approved Nov.1,2018.Published December 2018.Originallyapproved in 1977.Last previous edition approved in 2013 as C795 08(2013).DOI:10.1520/C0795-08R18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 chlorides from outside the system are concentrated at thesurface of the stainless steel.3,4,54.3 Studies have shown that insulation containing certainwater-soluble compounds have the capacity to retard or preventstress corrosion.Numerous materials thought to inhibit stresscorrosion cracking have been tried with varying deg

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开