ASTM_C_1349_-_17.pdf

Designation:C134917Standard Specification forArchitectural Flat Glass Clad Polycarbonate1This standard is issued under the fixed designation C1349;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers the quality requirements forcut sizes of glass clad polycarbonate(GCP)for use in buildingsas security,detention,hurricane/cyclic wind-resistant,blast andballistic-resistant glazing applications.1.2 Optical distortion and the evaluation thereof are notcurrently within the scope of the standard.Mockups arerecommended as a method to evaluate glass.(See AppendixX3.)1.3 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 Reference to these documents shall be the latest revisionunless otherwise specified by the authority applying thisspecification.2.2 ASTM Standards:2C162 Terminology of Glass and Glass ProductsC1036 Specification for Flat GlassC1048 Specification for Heat-Strengthened and Fully Tem-pered Flat GlassC1172 Specification for Laminated Architectural Flat GlassC1376 Specification for Pyrolytic and Vacuum DepositionCoatings on Flat GlassC1422 Specification for Chemically Strengthened Flat GlassC1503 Specification for Silvered Flat Glass MirrorD256 Test Methods for Determining the Izod PendulumImpact Resistance of PlasticsD543 Practices for Evaluating the Resistance of Plastics toChemical ReagentsD635 Test Method for Rate of Burning and/or Extent andTime of Burning of Plastics in a Horizontal PositionD638 Test Method for Tensile Properties of PlasticsD648 Test Method for Deflection Temperature of PlasticsUnder Flexural Load in the Edgewise PositionD790 Test Methods for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating Materi-alsD792 Test Methods for Density and Specific Gravity(Rela-tive Density)of Plastics by DisplacementD1003 Test Method for Haze and Luminous Transmittanceof Transparent PlasticsD1005 Test Method for Measurement of Dry-Film Thick-ness of Organic Coatings Using MicrometersD1044 Test Method for Resistance of Transparent Plastics toSurface AbrasionD3763 Test Method for High Speed Puncture Properties ofPlastics Using Load and Displacement SensorsE308 Practice for Computing the Colors of Objects by Usingthe CIE SystemE1886 Test Method for Performance of Exterior Windows,Curtain Walls,Doors,and Impact Protective SystemsImpacted by Missile(s)and Exposed to Cyclic PressureDifferentialsE1996 Specification for Performance of Exterior Windows,Curtain Walls,Doors,and Impact Protective SystemsImpacted by Windborne Debris in HurricanesF1233 Test Method for Security Glazing Materials AndSystemsF1642 Test Method for Glazing and Glazing Systems Sub-ject to Airblast Loadings1This specification is under the jurisdiction of ASTM Committee C14 on Glassand Glass Products and is the direct responsibility of Subcommittee C14.08 on FlatGlass.Current edition approved April 15,2017.Published June 2017.Originallyapproved in 1996.Last previous edition approved in 2010 as C1349 10.DOI:10.1520/C1349-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 F1915 Test Methods for Glazing for Detention Facilities2.3 ANSI Standard:Z97.1 Safety Glazing Materials Used in BuildingsSafetyPerformance Specifications and Methods of Tests32.4 Federal Document:CPSC 16 CFR 1201 Consumer Product Safety CommissionSafety Standard for Architectural Glazing Materials42.5 UL Standards5UL