ASTM_C_348-18.pdf

C348-182.913.35.0SYMMETRICAL ABOUT OL+10.04.5 mm o CLEARANCE HOLE IN END PLATE186.0DRILL AND TAP SIDE PL 13 mm DP FORM40.512 mm LG MACHINE SCREWS93.093.0TYPICAL 8 PLACES+25.03mmg12 mm LG DOWEL PINS10.0-160.0+10.0DRILL FOR PRESS FIT TO END PLATE15.0AND FORM DIVIDER3.03.0TYPICAL 8 PLACES.05013.(TYP7.040.0f13(TYP)40.0YMMETRICAL ABOUT C/L7.0160.01300.012(TYP)+3.5 mm o CLEARANCE HOLES IN GUIDE AND END PLATE+13(TYP)DRILL AND TAP FORM BAR 6 mm DP FOR17(TYP)M30.3515 mm LONG MACHINE SCREWS25(TYP)TYPICAL 2 PLACES3.5 mm o CLEARANCE HOLES IN END PLATEDRILL AND TAP FORM BAR 6 mm DP FORM3 x 0.35 x 8 mm LONG MACHINE SCREWSTYPICAL 4 PLACESNOTE:3.5 mm o CLEARANCE HOLES IN GUIDEDRILL AND TAP SIDE PL 9 mm DP FOR1.ALL DIMENSIONS IN MILLIMETERSM30.3515 mm LONG MACHINE SCREWSTYPICAL 2 PLACESDETAIL/TAMPER GUIDE ATTACHMENTScale:NoneFIG.2 Tamper Guide Attachmentappropriate diameter and height shall be obtained.End faces of the10.Procedurepedestal must be plane and parallel and at 90 to the axis of the cylinder.The upper face shall have a diameter of 77.5 mm.10.1 Proportioning,Consistency,and Mixing of Mortars-The proportioning,consistency,and mixing of the standard7.Materialsmortar shall be in accordance with the Procedure Section of7.1 Graded Standard Sand:Test Method C109/C109M.7.1.1 The sand used for making test specimens shall be10.2 Determination of Flow-The flow shall be determinednatural silica sand and conform to Specification C778.in accordance with Test Method C1437.8.Number of Specimens10.3 Molding Test Specimens:10.3.1 Immediately following completion of the flow test,8.1 Three or more specimens shall be made for each periodreturn the mortar from the flow table to the mixing bowlof test specified.Quickly scrape down into the batch the mortar that may havecollected on the side of the bowl and then remix the entire9.Preparing Specimen Moldsbatch 15 s at medium speed.Upon completion of mixing,the9.1 Prepare the specimen molds as prescribed in Testmixing paddle shall be shaken to remove excess mortar into theMethod C109/C109M.mixing bowl.Copyright by ASTM Intl(all rights reserved):Wed Jul 1010:43:33 EDT20193Downloaded/printed byCoventry University(Coventry University)pursuant to License Agreement.No further reproductions authorized.4C348-18153.37439,016120.00LD6NOTE:1.ALL DIMENSIONS IN MILLIMETERS118-4130.620.6DRILL AND PRESS FIT8.7a 74.76mm016mmGD0VwETP(2)1569.5 mm a9.5 mm o3.23212,701/2BALL BEARING4.0 mm o CLEARANCE HOLE484.8FOR M4 10.0 CAVEL 4.8 DP/M4 ISO FINE THD13424.0413.4TYP(2)5.6-39.75.e6.0 mm o CLEARANCE HOLE10DETAIL BASE PLATE AND SUPPORT EDGESScale:None(a)Base Plate and Support Edges40mCLEARANCE HOLE-27.0+十-27.0+CBORE 7.5 o x 5.0 DP127DRILL AND TAP DOWEL 4.8 DP/M4 ISO FINE THDFOR M4x 10.0MM LG CAP SCREW/TYP(2)6.3。-634.8 mm o CLEARANCE HOLECB0E8.009.6DPDRILL AND TAP M4 ISO FINE THD x 7.5 DP3.2RTYP阿FOR M4 x 26.0 mm LG FILLISTER HEAD TYP(2)3.20.495 mm MUSIC WIRE5 TURNS12.7 o BALL BEARING159329.5341.3GD0WE6.5一22637.920.6420.679+19.141219.179479.464.0 mm CLEARANCE HOLENOTE:1.ALL DIMENSIONS IN MILLIMETERSDETAIL CENTER-POINT LOADING COMPONENTScale:None(b)Center-Point Loading Component.FIG.3 Special Components for Adapting Compression Testing Machine for Testing 40 by 40 by 160-mm PrismsFIG.3 Special Components for Adapting Compression Testing Machine for Testing 40 by 40 by 160-mm PrismsCopyright by ASTM Intl(all rights reserved):Wed Jul 1010:43:33 EDT 2019 4Downloaded/printed byCoventry University(Coventry University)pursuant to License Agreement.No further reproductions authorized.