分享
ASTM_B_985_-_12_2016.pdf
下载文档

ID:184930

大小:166.44KB

页数:8页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_B_985_ _12_2016
Designation:B98512(Reapproved 2016)Standard Practice forSampling Aluminum Ingots,Billets,Castings and Finishedor Semi-Finished Wrought Aluminum Products forCompositional Analysis1This standard is issued under the fixed designation B985;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice describes procedures for sampling un-wrought aluminum ingots,billets,castings and finished orsemi-finished wrought aluminum products to obtain a repre-sentative sample for determining chemical composition.1.1.1 Chemical compositions determined from samples ob-tained in accordance with this standard practice may differfrom the bulk chemical composition determined from samplestaken when ingots or castings are poured.These differences canbeduetoelementalsegregationthatoccursduringsolidification,procedures that remove enriched material(forexample,ingot scalping),or procedures that remove depletedareas(for example,removal of the riser from a casting).1.1.2 Analysis of samples obtained from unwrought alumi-num ingots,billets,and castings and finished or semi-finishedwrought aluminum products can be used to determine if thepiece sampled meets The Aluminum Association,Inc.regis-tered chemical composition limits or other specified chemicalcomposition limits for the alloy.Analysis of such samples shallnot supersede the analysis of samples taken during pouring ofcastings or ingots in accordance with Practices E716 andanalyzed in accordance with Test Methods E34,E607,E1251,or EN 14242 and shall not be used for determining compliancewith chemical composition requirements for an entire cast lotor part thereof.NOTE1Pieces may include ingots,forgings,coils,sheets,extrusions,castings,and so forth.A single unwrought ingot or billet may producemultiple finished or semi-finished pieces.NOTE2Certification of entire cast lots should be determined usingsamples taken during pouring of castings or ingots in accordance withPractices E716 and analyzed in accordance with Test Methods E34,E607,E1251,or EN 14242.1.2 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard.Thevalues stated in each system may not be exact equivalents;therefore,each system shall be used independently of the other.Combining values from the two systems may result in non-conformance with the standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2B881 Terminology Relating to Aluminum-and Magnesium-Alloy ProductsE34 Test Methods for Chemical Analysis of Aluminum andAluminum-Base AlloysE135 Terminology Relating to Analytical Chemistry forMetals,Ores,and Related MaterialsE607 Test Method for Atomic Emission SpectrometricAnalysis Aluminum Alloys by the Point to Plane Tech-nique Nitrogen Atmosphere(Withdrawn 2011)3E716 Practices for Sampling and Sample Preparation ofAluminum and Aluminum Alloys for Determination ofChemical Composition by Spark Atomic Emission Spec-trometryE1251 Test Method for Analysis of Aluminum and Alumi-num Alloys by Spark Atomic Emission Spectrometry2.2 Other Standards:4EN 14242 Aluminum and Aluminum AlloyschemicalAnalysisinductively Coupled Plasma Optical EmissionSpectral Analysis3.Terminology3.1 For definitions of terms used in this Standard,refer toTerminologies B881 and E135.1This practice is under the jurisdiction of ASTM Committee B07 on LightMetals and Alloys and is the direct responsibility of Subcommittee B07.05 onTesting.Current edition approved Nov.1,2016.Published November 2016.Originallyapproved in 2012.Last previous edition approved in 2012 as B985 12.DOI:10.1520/B0985-12R16.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from European Committee for Standardization,Central Secretariat(CEN),rue de Stassart 36,B1050 Brussels,Belgium.http:/www.cen.eu/esearch.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.Summary of Practice4.1 The procedures described in this practice involve thecutting and drilling of aluminum products to obtain samples forsubsequent chemical analysis in accordance with Test MethodsE34,E607,E1251,or EN 14242.5.Significance and Use5.1 Products covered by this practice are unwrought alumi-num ingots,billets,and cast

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开