ASTM_C_1765_-_18.pdf

Designation:C176518Standard Specification forSteel Fiber Reinforced Concrete Culvert,Storm Drain,andSewer Pipe1This standard is issued under the fixed designation C1765;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers steel fiber reinforced concretepipe(SFRCP)of internal diameters 12-48 in.,intended to beused for the conveyance of sewage,industrial wastes,andstorm water and for the construction of culverts.NOTE1Experience has shown that the successful performance of thisproduct depends upon the proper selection of the pipe strength,the type ofbedding and backfill,the care that the installation conforms to theconstruction specifications,and provision for adequate inspection at theconstruction site.This specification does not include requirements forbedding,backfill,the relation ship between field load conditions and thestrength designation of pipe,or durability under unusual environmentalconditions.These requirements should be included in the project specifi-cation.1.2 The values stated in inch-pound units are to be regardedas standard.No other units of measurement are included in thisstandard.1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2A820/A820M Specification for Steel Fibers for Fiber-Reinforced ConcreteC33/C33M Specification for Concrete AggregatesC150/C150M Specification for Portland CementC260/C260M Specification for Air-Entraining Admixturesfor ConcreteC494/C494M Specification for Chemical Admixtures forConcreteC497 Test Methods for Concrete Pipe,Manhole Sections,orTileC595/C595M Specification for Blended Hydraulic CementsC618 Specification for Coal Fly Ash and Raw or CalcinedNatural Pozzolan for Use in ConcreteC822 Terminology Relating to Concrete Pipe and RelatedProductsC989/C989M Specification for Slag Cement for Use inConcrete and MortarsC1017/C1017M Specification for Chemical Admixtures forUse in Producing Flowing ConcreteC1602/C1602M Specification for Mixing Water Used in theProduction of Hydraulic Cement ConcreteE105 Practice for Probability Sampling of Materials3.Terminology3.1 DefinitionsFor definitions of terms relating to concretepipe not defined in this specification,see Terminology C822.3.2 DServicethe DTesttest load divided by a factor of safetyof 1.5.3.3 DTestthe load the pipe is required to support in thethree-edge bearing test expressed as a D-load.4.Classification4.1 Pipe furnished under this specification shall be desig-nated as Class I,II,III,IV,or V.The corresponding strengthrequirements are prescribed in Table 1.Special designs for pipestrengths not designated in Table 1 are permitted,provided allother requirements of this specification are met.5.Basis of Acceptance5.1 The acceptability of the pipe design shall be in accor-dance with Section 9.5.2 Unless designated by the owner at the time of,or beforeplacing an order,the pipe shall be accepted on the basis ofSections 10 and 11,and such material tests as are required in7.2,7.3,and 7.5.5.3 Age for AcceptancePipe shall be considered ready foracceptance when they conform to the requirements of thisspecification.1This test method is under the jurisdiction of ASTM Committee C13 onConcrete Pipe and is the direct responsibility of Subcommittee C13.02 onReinforced Sewer and Culvert Pipe.Current edition approved Oct.1,2018.Published October 2018.Originallyapproved in 2013.Last previous edition approved in 2016 as C1765-16.DOI:10.1520/C1765-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 6.Design and Manufacturing6.1 The manufacturer shall provide the following informa-tion regarding the pipe unless waived by the owner:6.1.1 Pipe design strength(DService).6.1.2 Physical CharacteristicsDiameter,wall thickness,laying length,and joint details.6.1.3 SteelFiberConcreteCompressiveStrengthMini