ASTM_C_1007_-_11a_2015.pdf

Designation:C100711a(Reapproved 2015)Standard Specification forInstallation of Load Bearing(Transverse and Axial)SteelStuds and Related Accessories1This standard is issued under the fixed designation C1007;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers the installation and erectionrequirements for load bearing(transverse and axial)steel studsand related accessories 0.0329 in.(0.836 mm)to 0.1120 in.(2.845 mm)thick.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 The text of this standard references notes and footnoteswhich provide explanatory material.These notes and footnotes(excluding those in tables and figures)shall not be consideredas requirements of the standard.2.Referenced Documents2.1 ASTM Standards:2C11 Terminology Relating to Gypsum and Related BuildingMaterials and SystemsC841 Specification for Installation of Interior Lathing andFurringC954 Specification for Steel Drill Screws for theApplicationof Gypsum Panel Products or Metal Plaster Bases to SteelStuds from 0.033 in.(0.84 mm)to 0.112 in.(2.84 mm)inThicknessC955 Specification for Load-Bearing(Transverse andAxial)Steel Studs,Runners(Tracks),and Bracing or Bridgingfor Screw Application of Gypsum Panel Products andMetal Plaster BasesC1063 Specification for Installation of Lathing and Furringto Receive Interior and Exterior Portland Cement-BasedPlaster2.2 American Iron and Steel Institute Publication(AISI):S100 North American Specification for the Design of Cold-Formed Steel Structural Members 2007 Edition32.3 American Welding Society Documents(AWS):D1.3 Specification for Welding Sheet Steel in Structures42.4 Military Specification:MIL-P-21035 Paint,High Zinc Dust Content,GalvanizingRepair52.5 Federal Specification:FF-P-395 Pin,Drive,Guided and Pin Drive,Power Actu-ated Fasteners for Power Actuated and Hand ActuatedFastening Tools5AISI COSP Code of Standard Practice for Cold-FormedSteel Structural Framing 2006 Edition53.Terminology3.1 Definitions shall be in accordance with TerminologyC11.3.2 Definitions of Terms Specific to This Standard:3.2.1 axial loads,nthose loads applied to a member in thesame plane as its major centroidal axis.3.2.2 cripple studs,nless than full height studs above aheader or below a sill.3.2.3 framing members,nstuds joist,runners(tracks),bridging and bracing and related accessories.3.2.4 header,nthe stud assembly or the track assembly,orboth,placed at a right angle to supporting studs that creates thetop of a framed opening.3.2.5 jack stud,na framing member which provides sup-port at the end of a header.3.2.6 panelized construction,nfabrication of framingmembers into an assembly prior to erection.3.2.7 sill,nthe stud assembly or the track assembly,orboth,placed at a right angle to supporting studs that creates thebottom of a framed opening.1This specification is under the jurisdiction of ASTM Committee C11 onGypsum and Related Building Materials and Systems and is the direct responsibilityof Subcommittee C11.03 on Specifications for theApplication of Gypsum and OtherProducts in Assemblies.Current edition approved Oct.1,2015.Published October 2015.Originallyapproved in 1983.Last previous edition approved in 2011 as C1007 11a.DOI:10.1520/C1007-11AR15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American Iron and Steel Institute(AISI),1140 ConnecticutAve.,NW,Suite 705,Washington,DC 20036,http:/www.steel.org.4Available from American Welding Society(AWS),550 NW LeJeune Rd.,Miami,FL 33126,http:/www.aws.org.5Available from Standardization Documents Order Desk,Bldg.4 Section D,700Robbins Ave.,Philadelphia,PA 19111-5094,Attn:NPODS.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.2.8 transverse loads,nthose loads applied to a memberin a plane perpendicular to its major centroidal axis.4.Storage of Materials4.1 Material shall be received and stored in accordance withAISI COSP F3 Delivery,Handling and Storage of Materials.5.Materials5.1 Framing membersSpecification C955.5.2 Zinc-rich paintMIL-P-21035.5.3 Steel drill screwsSpecification C954.Screws shallhave rust inhibitive coating suitable for the intended installa-tion.5.4 Power actuated drive pinsFF-P-395.6.Fastenings and Attachments6.1 Anchorage of the tracks to the structure shall be withmethods designed for th