ASTM_C_1063_-_17a.pdf

Designation:C106317aStandard Specification forInstallation of Lathing and Furring to Receive Interior andExterior Portland Cement-Based Plaster1This standard is issued under the fixed designation C1063;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification covers the minimum technical re-quirements for lathing and furring for the application ofexterior and interior portland cement-based plaster,as inSpecifications C841 or C926.These requirements do not bydefault define a unit of work or assign responsibility forcontractual purposes,which is the purview of a contract orcontracts made between contracting entities.1.2 Where a fire resistance rating is required for plasteredassemblies and constructions,details of construction shall be inaccordance with reports of fire tests of assemblies that havemet the requirements of the fire rating imposed.1.3 Where a specific degree of sound control is required forplastered assemblies and constructions,details of constructionshall be in accordance with official reports of tests conducted inrecognized testing laboratories in accordance with the appli-cable requirements of Test Method E90.1.4 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2A641/A641M Specification for ZincCoated(Galvanized)Carbon Steel WireA653/A653M Specification for Steel Sheet,Zinc-Coated(Galvanized)or Zinc-Iron Alloy-Coated(Galvannealed)by the Hot-Dip ProcessB69 Specification for Rolled ZincB221 Specification for Aluminum and Aluminum-Alloy Ex-truded Bars,Rods,Wire,Profiles,and TubesC11 Terminology Relating to Gypsum and Related BuildingMaterials and SystemsC841 Specification for Installation of Interior Lathing andFurringC847 Specification for Metal LathC926 Specification for Application of Portland Cement-Based PlasterC933 Specification for Welded Wire LathC954 Specification for Steel Drill Screws for theApplicationof Gypsum Panel Products or Metal Plaster Bases to SteelStuds from 0.033 in.(0.84 mm)to 0.112 in.(2.84 mm)inThicknessC1002 Specification for Steel Self-Piercing Tapping Screwsfor Application of Gypsum Panel Products or MetalPlaster Bases to Wood Studs or Steel StudsC1032 Specification for Woven Wire Plaster BaseD1784 Specification for Rigid Poly(Vinyl Chloride)(PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC)CompoundsD4216 Specification for Rigid Poly(Vinyl Chloride)(PVC)and Related PVC and Chlorinated Poly(Vinyl Chloride)(CPVC)Building Products CompoundsE90 Test Method for Laboratory Measurement of AirborneSound Transmission Loss of Building Partitions andElements1This specification is under the jurisdiction of ASTM Committee C11 onGypsum and Related Building Materials and Systems and is the direct responsibilityof Subcommittee C11.03 on Specifications for theApplication of Gypsum and OtherProducts in Assemblies.Current edition approved June 1,2017.Published June 2017.Originallyapproved in 1986.Last previous edition approved in 2017 as C1063 17.DOI:10.1520/C1063-17a.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.Terminology3.1 DefinitionsFor definitions relating to ceilings andwalls,see Terminology C11.3.2 Definitions of Terms Specific to This Standard:3.2.1 building enclosure,nsystem of building assembliesand materials designed and installed in such a manner as toprovide a barrier between different environments.3.2.2 control joint,na joint that accommodates movementof plaster shrinkage and curing along predetermined,usuallystraight,lines.3.2.3 expansion jo