温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_1610_
_18
Designation:D161018Standard Practice forConditioning Leather and Leather Products for Testing1This standard is issued under the fixed designation D1610;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This practice covers the conditioning of all units andspecimens of leather and leather products prior to testing andthe conditions under which they should be tested.This practicedoes not apply to wet blue.1.2 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:D1517 Terminology Relating to LeatherE337 Test Method for Measuring Humidity with a Psy-chrometer(the Measurement of Wet-and Dry-Bulb Tem-peratures)2.2IU Standards:IUP/3 Conditioning23.Terminology3.1 Definitions:3.1.1 For definitions of leather terms used in this practice,refer to Terminology D1517.3.1.2 standard atmospheric conditionsfor leather andleather testing,one of two sets of conditions:(1)a temperature of 23 6 2C(73.4 6 3.6F)and a relativehumidity of 50 6 4%(2)a temperature of 20 6 2C(68.0 6 3.6F)and a relativehumidity of 65 6 4%.Condition set(1)is used as the standard for leather testing inNorth America and condition set(2)is used as the standard forleather testing in Europe and Japan.4.Summary of Test Method4.1 The conditioning prescribed in this practice is designedto obtain reproducible test results on leather and leatherproducts by the standardization of the relative humidity andtemperature conditions to which the leather or leather productis subjected prior to and during testing.5.Significance and Use5.1 Temperature and relative humidity have an influence onmany of the physical properties of leather.Depending onenvironmental conditions the moisture content in leather mayvary significantly.Standardized conditioning in part allows forreliable comparisons to be made among different leather andleather products,and among different laboratories.6.Apparatus6.1 Room,in which the standard atmosphere is automati-cally maintained.6.2 PsychrometerEither a sling psychrometer,or a station-ary type psychrometer having the air circulated over thethermometer bulbs.NOTE1It is preferable to draw air over the thermometer bulb ratherthan blow air,from a fan source,over them.Heat from the fan may causeerrors in the readings.6.3 ThermometersThe thermometers should conform ap-proximately to the following requirements:range 0 to 52C(32to 122 F);graduation 0.2C(0.5F).They should be matchedto within 0.1C(0.25F)throughout the range used.Calibratethermometer in accordance with manufacturers instructions.NOTE2Under ordinary conditions,an error of 1%in relativehumidity corresponds to an error of approximately 0.1C(0.2F)in thewet-bulb depression.6.4 Chamber for maintaining 65%relative humidityArelative humidity of 65 6 2%at 20 6 2C can be maintainedin a closed space by the use of a saturated solution of certain1This practice is under the jurisdiction ofASTM Committee D31 on Leather andis the direct responsibility of Subcommittee D31.07 on Physical Properties.Thispractice was developed in cooperation with the American Leather Chemists Assn.Current edition approved Oct.1,2018.Published October 2018.Originallyapproved in 1984.Last previous edition approved in 2013 as D1610 01(2013).DOI:10.1520/D1610-18.2Journal of the Society of Leather Trades Chemists,Vol XLII,No.12,pp386387.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 salts in water(in which the solid phase is present in excess)3ora sulfuric acid solution.The solution should be placed in alarge shallow dish inside the closed vessel.Continuous circu-lation of air inside the vessel is essential.Appropriate saturatedsalt solutions can be prepared from either pure ammoniumnitrate or pure sodium nitrate.NOTE3Creeping of the solid ph