ASTM_D_1073_-_16_2022.pdf

Designation:D107316(Reapproved 2022)Standard Specification forFine Aggregate for Asphalt Paving Mixtures1This standard is issued under the fixed designation D1073;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers fine aggregate for use inasphalt paving mixtures.1.2 This specification is intended to describe material froma single source.When material from two or more sources is tobe blended to produce a grading to meet requirements in otherspecifications for asphalt paving mixtures,the grading require-ments of Table 1 of this specification are not applicable.NOTE1When obtaining materials from two or more sources that areto be blended to produce the final mix,it is recommended that thespecifying or the ordering agency specify the alternative gradings andblend ratios to be supplied.1.3 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.Sieve numbers shown in the text and Table 1 arelabels only and are included for ease of reference of the user ofthis standard.1.4 The text of this standard references notes and footnoteswhich provide explanatory material.These notes and footnotes(excluding those in tables and figures)shall not be consideredas requirements of the standard.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C88/C88M Test Method for Soundness of Aggregates byUse of Sodium Sulfate or Magnesium SulfateC117 Test Method for Materials Finer than 75-m(No.200)Sieve in Mineral Aggregates by WashingC125 Terminology Relating to Concrete and Concrete Ag-gregatesC136/C136M Test Method for Sieve Analysis of Fine andCoarse AggregatesC294 Descriptive Nomenclature for Constituents of Con-crete AggregatesD8 Terminology Relating to Materials for Roads and Pave-mentsD75/D75M Practice for Sampling AggregatesD3665 Practice for Random Sampling of Construction Ma-terialsD4318 Test Methods for Liquid Limit,Plastic Limit,andPlasticity Index of SoilsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with Specifications3.Terminology3.1 Definitions:3.1.1 For defining aggregate types,see Descriptive Nomen-clature C294,and Terminologies D8 and C125.3.1.2 expanded shale,n;expanded clay,n;expanded slate,n;the product resulting from the expanding of selectedmaterials(shale,clay,or slate)in a rotary kiln at temperaturesover 1000 C.4.Ordering Information4.1 Orders for material under this specification shall includethe following:4.1.1 This specification designation including year,4.1.2 Grading(6.2 and Table 1),or alternative gradingdesignated by the purchaser,4.1.3 Supplementary requirement for sulfate soundness,ifrequired,including salt to be used(See Supplementary Re-quirement S1),and4.1.4 Any exceptions or additions to this specification.5.General Characteristics5.1 Fine aggregate is aggregate passing the 9.5 mm(38in.)sieve and almost entirely passing the 4.75 mm(No.4)sieve.Itshall consist of natural sand;or of manufactured fine aggregate1This specification is under the jurisdiction of ASTM Committee D04 on Roadand Paving Materials and is the direct responsibility of Subcommittee D04.50 onAggregate Specifications.Current edition approved July 1,2022.Published July 2022.Originally approvedin 1949.Last previous edition approved in 2016 as D1073 16.DOI:10.1520/D1073-16R22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1from crushed stone,crushed blast-furnace slag,or crushedgravel;or crushed or uncrushed expanded shale,expandedclay,or expanded slate;or combinations thereof.It shall consistof hard,tough grains,free of injurious amounts of clay,loam,or other deleterious substances.6.Physical Properties6.1 To determine conformance to this specification,eachvalue for grading(and sulfa