分享
ASTM_C_62_-_17.pdf
下载文档

ID:184253

大小:238.84KB

页数:4页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_C_62_ _17
Designation:C6217Standard Specification forBuilding Brick(Solid Masonry Units Made From Clay orShale)1This standard is issued under the fixed designation C62;the number immediately following the designation indicates the year of originaladoption or,in the case of revision,the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification covers brick intended for both struc-tural and nonstructural masonry where external appearance isnot a requirement.The brick are prismatic units available in avariety of sizes,shapes,textures,and colors.The specificationdoes not cover brick intended for use as facing units or wheresurface appearance is a requirement.If brick are required tohave a particular color,texture,finish,uniformity,or limits oncracks,warpage,or other imperfections detracting from theappearance they are purchased under Specification C216.Thisspecification does not cover brick intended for use as pavingbrick(see Specification C902).1.2 The property requirements of this standard apply at thetime of purchase.The use of results from testing of brickextracted from masonry structures for determining confor-mance or nonconformance to the property requirements(Sec-tion 4)of this standard is beyond the scope of this standard.1.3 Brick are manufactured from clay,shale,or similarnaturally occurring earthy substances and subjected to a heattreatment at elevated temperatures(firing).The heat treatmentmust develop sufficient fired bond between the particulateconstituents to provide the strength and durability requirementsof this specification(see Terminology C1232).1.4 Brick are shaped during manufacture by molding,pressing,or extrusion,and the shaping method is a way todescribe the brick.1.5 The text of this standard references notes and footnoteswhich provide explanatory material.These notes and footnotes(excluding those in tables and figures)shall not be consideredas requirements of the standard.1.6 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.7 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C67 Test Methods for Sampling and Testing Brick andStructural Clay TileC216 Specification for Facing Brick(Solid Masonry UnitsMade from Clay or Shale)C902 Specification for Pedestrian and Light Traffic PavingBrickC1232 Terminology for Masonry3.Terminology3.1 DefinitionsFor definitions relating to building brick,refer to Terminology C1232.4.Classification4.1 GradesGrades classify brick according to their resis-tance to damage by freezing and thawing when saturated at amoisture content not exceeding the 24-h cold water absorption.Three grades of building brick are covered and the require-ments are given in Section 5.4.1.1 Grade SW(Severe Weathering)Brick intended foruse where high resistance to damage caused by cyclic freezingand thawing is desired.4.1.2 Grade MW(Moderate Weathering)Brick intendedfor use where moderate resistance to cyclic freezing andthawing damage is permissible.1This specification is under the jurisdiction of ASTM Committee C15 onManufactured Masonry Units and is the direct responsibility of SubcommitteeC15.02 on Brick and Structural Clay Tile.Current edition approved Oct.1,2017.Published October 2017.Originallyapproved in 1927.Last previous edition approved in 2013 as C62 13a.DOI:10.1520/C0062-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 4.1.3 Grade NW(Negligible Weathering)Brick intendedfor use where little resistance to cyclic freezing and thawingdamage is acceptable.NOTE1The word“saturated,”with respect to this standard,refers tothe condition of a brick that has absorbed water to an amount equal to thatresulting from submersion in room temperatur

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开