分享
ASTM_D_1694_-_95_2000.pdf
下载文档

ID:184058

大小:49.85KB

页数:4页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_1694_ _95_2000
Designation:D 1694 95(Reapproved 2000)An American National StandardStandard Specification forThreads 60(Stub)for“Fiberglass(Glass-Fiber-Reinforced Thermosetting-Resin)Pipe1This standard is issued under the fixed designation D 1694;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers the geometry and dimensionsof a thread system for fiberglass pipe.1.2 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation purposes only.NOTE1There is no similar or equivalent ISO standard.2.Referenced Documents2.1 ASTM Standards:D 883 Terminology Relating to Plastics2D 1600 Terminology for Abbreviated Terms Relating toPlastics2E 177 Practice for Use of the Terms Precision and Bias inASTM Test Methods3F 412 Terminology Relating to Plastic Piping Systems43.Terminology3.1 GeneralDefinitions are in accordance with Termi-nologies D 883 and F 412 and abbreviations are in accordancewith Terminology D 1600,unless otherwise indicated.3.2 Definitions of Terms Specific to This Standard:3.2.1 fiberglass pipe,na tubular product containing glassfiber reinforcements embedded in or surrounded by curedthermosetting resin;the composite structure may containaggregate,granular,or platelet fillers,thixotropic agents,pig-ments,or dyes;thermoplastic or thermosetting liners or coat-ings may be included.4.Thread Geometry and Dimensions4.1 GeometryThe geometry of the thread form shall be inaccordance with Fig.1 and shall be defined as modified by theAmerican National Standard 60 stub thread.The male threadmay be preceded by a cylindrical pilot of length equal to twothread pitches and the outside diameter equal to or less than thetheoretical diameter of the thread if it were extended to the endof the pilot.4.2 DimensionsAll sizes of pipe from 112to 20 in.indiameter inclusive shall have 8 threads per inch,tapered 1 in 32on the diameter,and shall conform to the dimensions specifiedin Table 1.The geometry of the gage to measure the 60 stubshall be in accordance with Fig.2.The dimensions andtolerances for all size gages shall conform to the dimensionslisted in Table 2 and Table 3,respectively.5.Precision of Measurement5.1 The measurement experience of an individual manufac-turer of threads in accordance with this specification has shownthe following indexes of precision:5.1.1 Micrometer CaliperThe multi-micrometer-operator-specimen-day precision is 60.001 in.(0.025 mm)(2S)asdefined in Practice E 177.5.1.2 OpticalComparatorwithMicrometerHeadReadoutThe single-optical comparator and multi-operator-specimen-day precision is 60.001 in.(0.025 mm)(2S)asdefined in Practice E 177.6.Keywords6.1 fiberglass pipe;pipe;thread dimensions;threads1This specification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct responsibility of Subcommittee D20.23 on ReinforcedPlastic Piping Systems.Current edition approved March 10,2000.Published June 2000.Originallypublished as D 1694 59.Last previous edition D 1694 95.2Annual Book of ASTM Standards,Vols 08.01 and 08.04.3Annual Book of ASTM Standards,Vols 04.01 and 14.02.4Annual Book of ASTM Standards,Vol 08.04.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.FIG.1 Thread Geometry(see Table 1)TABLE 1Theoretical DimensionsPipe Thread,in.(mm)(see Fig.1)NOTE1Tolerance on lead per inch(25.4 mm)60.003 in.(60.076mm),cumulative 60.006 in.(60.152 mm).NOTE2All sizes 0.125-in.(3.175-mm)pitch.NOTE3 Thread will make up with ring gage shown in Fig.2.NOTE4All dimensions are given up to five decimal places only toavoid errors in computations,not to indicate required precision.NominalPipeSize,in.AL1BAin.mmin.mmin.mm1121.75044.451.12528.581.9942250.653221.93849.231.31333.352.4750962.86732122.12553.981.50038.102.9809475.715932.37560.321.75044.453.6137591.78923122.50063.501.87547.624.11765104.588342.62566.682.00050.804.62156117.38764122.75069.852.12553.985.12547130.186952.87573.022.25057.155.69237144.58625123.00076.202.37560.326.13328155.785363.12579.382.50063.506.76219171.759683.37585.722.75069.858.77000222.7580103.50088.902.87573.0210.89890276.8321123.50088.902.87573.0212.89890327.6321143.50088.902.87573.0214.14890359.3821163.50088.902.87573.0216.14890410.1821183.50088.902.87573.0218.14890460.9821203.50088.902.87573.0220.14890511.7821APitch diameter of hand-tight plane.D 1694 95(2000)2FIG.2 Geometry of Thread Gage(see Table 2)TABLE 2 Theoretical DimensionsPipe Thread Gage,in.(mm)(see Fig.2)NOTE1All dimensions are given up to five decimal places only to avoid errors in computations,not to indicate required precision.Nominal PipeSize,in.CDEAL1in.mmin.mmin.mmin

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开