ASTM_D_2051_-_14_2022.pdf

Designation:D205114(Reapproved 2022)Standard Test Method forDurability of Finish of Zippers to Laundering1This standard is issued under the fixed designation D2051;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of the dura-bility of the enamel or other decorative coating of a zipperwhen subjected to laundering.1.2 The values stated in SI units are to be regarded asstandard.The values given in parentheses after SI units areprovided for information only and are not considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD2050 Terminology Relating to Subassemblies Used in theManufacture of TextilesD2052 Test Method for Colorfastness of Zippers to Dry-cleaningD2053 Test Method for Colorfastness of Zippers to LightD2054 Test Method for Colorfastness of Zipper Tapes toCrockingD2057 Test Method for Colorfastness of Zippers to Laun-deringD2058 Test Method for Durability of Finish of Zippers toDrycleaningD2059 Test Method for Resistance of Zippers to Salt Spray(Fog)D2060 Test Methods for Measuring Zipper DimensionsD2061 Test Methods for Strength Tests for ZippersD2062 Test Methods for Operability of Zippers2.2 AATCC Method:Method 61Colorfastness to Washing,Domestic;andLaundering,Commercial:Accelerated33.Terminology3.1 DefinitionsFor definitions of zipper terms used in thisstandard,refer to Terminology D2050.For definitions of othertextile terminology used in this standard,refer to TerminologyD123.4.Summary of Test Method4.1 Specimens are laundered in laboratory equipment at alow liquor-to-goods ratio under conditions of temperature,bleaching,and abrasive action that produce the effect ofrepeated launderings in a conveniently short time.The zippercoating is abraded by the throw,slide,and impact of anappropriate number of steel balls.The effects of the test onzipper coating are evaluated by noting the loss of coating onthe zipper chain or components,or both.5.Significance and Use5.1 Test Method D2051 is useful for testing to determine theeffect of repeated laundering on the appearance of the decora-tive coating of a zipper.5.2 This test method is considered satisfactory for accep-tance testing of commercial shipments because the method hasbeen used extensively in the trade for acceptance testing.5.2.1If there are differences of practical significancebetween reported test results for two laboratories(or more),comparative test should be performed to determine if there is astatistical bias between them,using competent statistical assis-tance.As a minimum,the test samples should be used that areas homogeneous as possible,that are drawn from the materialfrom which the disparate test results were obtained,and thatare randomly assigned in equal numbers to each laboratory for1This test method is under the jurisdiction ofASTM Committee D13 on Textilesand is the direct responsibility of Subcommittee D13.54 on Subassemblies.Themethod was developed in cooperation with the Slide Fastener Association,Inc.Current edition approved March 1,2022.Published March 2022.Originallyapproved in 1961.Last previous edition approved in 2014 as D2051 14.DOI:10.1520/D2051-14R22.2For referenced ASTM standards,visit the ASTM web site,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM web site.3Technical Manual of the American Association of Textile Chemists andColorists,P.O.Box 12215,Research Triangle Park,NC 27709.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1testing.Other materials with established test values may beused for this purpose.The test results from the two laboratoriesshould be compared using a statistical te