分享
ASTM_D_1931_-_99_2004.pdf
下载文档

ID:183072

大小:55.12KB

页数:2页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_1931_ _99_2004
Designation:D 1931 99(Reapproved 2004)An American National StandardStandard Specification forFully Cured Silicone Rubber-Coated Glass Fabric and Tapesfor Electrical Insulation1This standard is issued under the fixed designation D 1931;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers fully cured silicone rubber-coated glass fabric in sheet form,full-width rolls,and tapes tobe used as electrical insulation.2.Referenced Documents2.1 ASTM Standards:2D 618 Practice for Conditioning Plastics for TestingD 1458 Test Methods for Fully Cured Silicone Rubber-Coated Glass Fabric and Tapes for Electrical InsulationD 1711 Terminology Relating to Electrical Insulation3.Terminology3.1 Definitions:3.1.1 For definitions of terms used in this specification,referto Terminology D 1711.4.Ordering Information4.1 Orders for material covered by this specification shallinclude the following information:4.1.1 Form(see Section 1),4.1.2 Desired nominal thickness,width,length,or weight,4.1.3 Number of rolls per package,4.1.4 Marking of packages,and,4.1.5 Whether mica dusting is required or not.5.Materials and Manufacture5.1 The glass fabric and the silicone rubber shall be of goodcommercial quality and shall be such as to produce a productthat will meet the requirements of this specification.Thesurface of the coated fabric shall be free of blisters,the coatedfabric shall be free of wrinkles and creases,and the goods shallbe free of any dust or dirt such as might be picked up due to astatic charge during processing.5.2 The material shall not be spliced unless agreed upon bythe purchaser and the manufacturer.If necessary to splice,thefollowing criteria may be used as a guide:in any givenshipment,90%should have no splice;the remaining 10%may have one splice and this should be flagged.The manner ofsplicing shall be agreed upon between the purchaser and theseller.6.Dimensional Requirements(Finished Cloth)6.1 WidthFull-width rolls and sheets shall be 91 6 2 cm(36 6 1 in.)in width,and shall be supplied trimmed to not lessthan 89 cm(35 in.)wide,unless otherwise specified.Individualmeasurements on tapes shall vary not more than 0.8 mm(132in.)from the specified width for tapes 38 mm(112in.)or lessin width,nor more than 1.6 mm(116in.)for tapes over 38 mmin width.6.2 LengthThe nominal length or weight shall be asspecified in the purchase order.The measured lengths ofindividual rolls or sheets shall be not less than that specified.7.Test Methods7.1 Appropriate sampling and test methods conforming toTest Methods D 1458 shall be used to determine the confor-mity of materials to this specification.8.Physical and Electrical Requirements8.1 The properties of the silicone rubber-coated glass fabricand tapes shall conform to those prescribed in Table 1.9.Rejection and Rehearing9.1 The purchaser reserves the right to reject any part of theshipment that does not conform to the requirements forpackaging and marking as specified in Section 10.9.2 The failure of 20%or more of the sample rolls or sheetsto conform to any one of the requirements given in Sections 5,6,7,and 8 shall constitute cause for rejection of the entireshipment without further tests.1This specification is under the jurisdiction of ASTM Committee D09 onElectrical and Electronic Insulating Materials and is the direct responsibility ofSubcommittee D09.07 on Flexible and Rigid Insulating Materials.Current edition approved Oct.10,1999.Published November 1999.Originallyapproved in 1961.Last previous edition approved in 1994 as D 1931 94.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.9.3 The failure of a sample roll to conform to the require-ments of one or more of the sections noted in 9.2 shall becounted as only one roll failure.10.Packaging and Package Marking10.1 PackagingRolls of silicone rubber-coated glass fab-ric,either in fullwidth rolls or slit tape form,shall bewrapped in such manner as to maintain the rolls in a firm andcompact condition and to protect the contents of the packagefrom mechanical damage,moisture,and contamination duringshipment.Sheets shall be packaged with equal care forprotection during shipment.10.2 MarkingShipping containers shall be marked withthe name of the manufacturer,catalog number,lot number,color,thickness,width,yardage,or weight,and date ofmanufacture.11.Keywords11.1 electrical insulation;silicone rubber-coated glass fabricASTM International takes no position respecting the validity of any pa

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开