分享
ASTM_D_1987_-_18.pdf
下载文档

ID:182628

大小:157.64KB

页数:6页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_1987_ _18
Designation:D198718Standard Test Method forBiological Clogging of Geotextile or Soil/Geotextile Filters1This standard is issued under the fixed designation D1987;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method is used to determine the potential for,and relative degree of,biological growth which can accumulateon geotextile or geotextile/soil filters.1.2 This test method uses the measurement of flow ratesover an extended period of time to determine the amount ofclogging.1.3 This test method can be adapted for nonsaturated as wellas saturated conditions.1.4 This test method can use constant head or falling headmeasurement techniques.1.5 This test method can also be used to give an indicationas to the possibility of backflushing,biocide treatment,or both,for remediation purposes if biological clogging does occur.1.6 The values in SI units are to be regarded as the standard.The values provided in inch-pound units are for informationonly.1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD1776 Practice for Conditioning and Testing TextilesD4354 Practice for Sampling of Geosynthetics and RolledErosion Control Products(RECPs)for TestingD4439 Terminology for GeosyntheticsD4491 Test Methods for Water Permeability of Geotextilesby PermittivityD5101 Test Method for Measuring the Filtration Compat-ibility of Soil-Geotextile SystemsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test MethodG22 Practice for Determining Resistance of Plastics toBacteria(Withdrawn 2002)33.Terminology3.1 Definitions:3.1.1 aerobic,na condition in which a measurable volumeof air is present in the incubation chamber or system.3.1.1.1 DiscussionIn geotextiles,this condition can poten-tially contribute to the growth of microorganisms.3.1.2 anaerobic,na condition in which no measurablevolume of air is present in the incubation chamber or system.3.1.2.1 DiscussionIn geotextiles,this condition cannotcontribute to the growth of microorganisms.3.1.3 back flushing,na process by which liquid is forcedin the reverse direction to the flow direction.3.1.3.1 DiscussionIn other drainage application areas,this process is commonly used to free clogged drainagesystems of materials that impede the intended direction of flow.3.1.4 biocide,na chemical used to kill bacteria and othermicroorganisms.3.1.5 geotextile,na permeable geosynthetic comprisedsolely of textiles.3.1.6 permeability,nthe rate of flow of a liquid under adifferential pressure through a material.3.1.6.1 DiscussionIn geotextiles,permeability refers tohydraulic conductivity.3.1.7 permittivity,()(t1),nof geotextiles,the volumetricflow rate of water per unit,in a cross-sectional area head underlaminar flow conditions.1This test method is under the jurisdiction of ASTM Committee D35 onGeosynthetics and is the direct responsibility of Subcommittee D35.02 on Endur-ance Properties.Current edition approved Feb.1,2018.Published February 2018.Originallyapproved in 1991.Last previous edition approved in 2016 as D1987 07(2016).DOI:10.1520/D1987-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.2 For definitions of other terms used in this test method,refer to Terminologies D123 and D4439.4.Summary of Test Method4.1 A geotextile filter specimen or geotextile/soil filtercomposite specimen is positioned in a flow column so that adesignated liquid flows through it under either constant orfalling

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开