分享
ASTM_D_1725_-_12_2019.pdf
下载文档

ID:182560

大小:77.63KB

页数:3页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_1725_ _12_2019
Designation:D172512(Reapproved 2019)Standard Practice forPreparing Resin Solutions for Viscosity Measurement byBubble Time Method1This standard is issued under the fixed designation D1725;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice provides instructions for preparing resinsolutions viscosity measurement by bubble time method.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.For specific hazard statements,see Section 7.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D154 Guide for Testing of Varnishes(Withdrawn 2018)3D1545 Test Method for Viscosity of Transparent Liquids byBubble Time MethodD6440 Terminology Relating to Hydrocarbon ResinsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method2.2 Other Document:OSHA Regulations,29 CFR,paragraphs 19.10.1000 and1910.120043.Terminology3.1 For definitions related to hydrocarbon resins see Termi-nology D6440.4.Summary of Practice4.1 Solid resins are dissolved in organic solvents by cold-cut or hot-cut methods in the laboratory.The viscosity of suchprepared solutions,or of commercial solutions of resins is thendetermined by the bubble time method(Test Method D1545).The bubble seconds are approximately equal to stokes.5.Apparatus5.1 Bath,constant-temperature,consisting of a cylindricalglass jar of about 5-gal capacity,or an aquarium tank withcontrols capable of maintaining the temperature at 25 6 0.1Cwith water as the bath medium.5.2 Bottles,225-mL(8-oz),wide-mouth,screw cap.5.3 Cellophane,sheet,cut into 102 or 127-mm(4 or 5-in.)squares.5.4 Corks,No.2 short taper,to fit viscosity tubes.5.5 Holder for Viscosity Tubes,preferably a mechanicalholder5with rack and pinion for inverting the tubes.The holdershould be checked with a small level and T-square to makecertain it holds the tubes in an exact vertical position afterbeing placed in the constant-temperature bath.5.6 Bottle Shaker,preferably one which will give end-over-end agitation.1This practice is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.33 on Polymers and Resins.Current edition approved June 1,2019.Published June 2019.Originallyapproved in 1960.Last previous edition approved in 2012 as D1725 12.DOI:10.1520/D172512R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from U.S.Government Printing Office Superintendent of Documents,732 N.Capitol St.,NW,Mail Stop:SDE,Washington,DC 20401,http:/www.access.gpo.gov.5Suitable mechanical viscosity tube holders are available from various labora-tory supply companies.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 5.7 Timing Device,such as a stopwatch or electric stopclock capable of being read to a precision of 0.1 s.5.8 Viscosity Tubes,of clear glass and flat bottoms,having10.65 6 0.025-mm inside diameter and 114 6 1-mm outsidelength.Plainly legible lines shall be located on the tubes asfollows:27 0.5 mm100 0.5 mm108 0.5 mmAll distances shall be measured from the bottom outside ofthe tube.The distance between the first and second lines shallbe 73 6 0.5 mm.6.Solvent6.1 The solvent used should be mutually agreed uponbetween the purchaser and the manufacturer.Toluene,xylene,mineral spirits,alcohols,etc.,are used for the preparation ofsolutions of resins.For a given resin,the viscosity obtainedwill depend on the solvent used.In case of dispute,b

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开