ASTM_D_3462_-_D_3462M_-_19.pdf

Designation:D3462/D3462M19Standard Specification forAsphalt Shingles Made from Glass Felt and Surfaced withMineral Granules1This standard is issued under the fixed designation D3462/D3462M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers asphalt roofing in shingleform,composed of glass felt or felts impregnated and coatedon both sides with asphalt,and surfaced on the weather sidewith mineral granules.This specification is designed for theevaluation of products as manufactured.The test methods,physical requirements,and minimum masses are to be mea-sured immediately after packaging or at a reasonable time,asagreed upon between buyer and seller,after manufacture andbefore installation.Physical and performance requirementsafter application and during in-service use of the productsdescribed herein are beyond the scope of this material speci-fication.1.2 Shingles meeting this specification are intended to beapplied with a headlap of not less than 51 mm 2 in.1.3 The shingles shall be supplied with a factory-appliedself-sealing adhesive or be designed to be locked togetherduring installation of the shingles.1.4 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.5 The following safety hazards caveat pertains only to thetest method described in this specification:This standard doesnot purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the user of thisstandard to establish appropriate safety,health,and environ-mental practices and determine the applicability of regulatorylimitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D5/D5M Test Method for Penetration of Bituminous Mate-rialsD36/D36M Test Method for Softening Point of Bitumen(Ring-and-Ball Apparatus)D228/D228M Test Methods for Sampling,Testing,andAnalysis of Asphalt Roll Roofing,Cap Sheets,andShingles Used in Roofing and WaterproofingD1079 Terminology Relating to Roofing and WaterproofingD1922 Test Method for Propagation Tear Resistance ofPlastic Film and Thin Sheeting by Pendulum MethodD3161/D3161M Test Method for Wind-Resistance of SteepSlope Roofing Products(Fan-Induced Method)D4977/D4977M Test Method for Granule Adhesion to Min-eral Surfaced Roofing by AbrasionE108 Test Methods for Fire Tests of Roof CoveringsF1667 Specification for Driven Fasteners:Nails,Spikes,andStaples3.Terminology3.1 Definitions:3.1.1 For definitions of terms,see Terminology D1079.3.1.2 For testing purposes,under Test Methods D228/D228M,glass felt shall be considered as felt.4.Materials and Manufacture4.1 The glass felt shall be a thin porous sheet composedpredominately of fine glass fibers uniformly deposited in anonwoven pattern.It is permitted to reinforce the glass feltwith random or parallel-oriented glass yarns,or both,which arepermitted to be gathered or twisted,bonded or unbonded.Thefelt shall contain a substantially water-insoluble binding agent.4.2 In the process of manufacture,one or more thicknessesof glass felt shall be impregnated with an asphaltic material.1This specification is under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.02on Steep Roofing Products and Assemblies.Current edition approved Feb.1,2019.Published March 2019.Originallyapproved in 1983.Last previous edition approved in 2016 as D3462/D3462M 16.DOI:10.1520/D3462_D3462M-19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 When more than one thickness of felt is used,the mats shall beadhered to each other with a continuous layer of