ASTM_D_1403_-_10_rus.pdf

D 140310 310/84(92)STANDARD TEST METHODS FOR CONE PENETRATION OF LUBRICATING GREASE USING ONE-QUARTER AND ONE-HALF SCALE CONE EQUIPMENT 2016 ():2873-16/ASTM :18.04.2016 -,.9,-49,-1,119049.:(499)236-54-49:(499)230-13-72 E-mail:interstgost.ru http:/www.interstandart.ru/(ASTM International)100 rr Harbor Drive,West Conshohocken,PA 19428,USA.ASTM International ,ASTM International.-,ASTM International ,.This translation is executed by FBU“CIC“Interstandard”of Federal Agency on Technical Regulating and Metrology under the license of American Society for Testing and Materials(ASTM International)100 rr Harbor Drive,West Conshohocken,PA 19428,USA.ASTM International does not approve and does not confirm these translations and in any cases only the English version published with a sign of ASTM International copyright can be considered as the original version.Reproduction of the specified translations by any Party,except for ASTM International or FBU“CIC“Interstandard”,is strictly forbidden according to the USA legislation and international copyright.ASTM D 1403-10 1 D 140310 310/84(92)1 D 1403;,.()1.1.1 1/4 1/2 .1 ASTM D02 D02.G0.02 .IP/,.1 2010.2010.1956.2007.D 1403-02(2007).DOI:10.1520/D1403-10.ASTM D 1403-10 2 1.2 ,.1.3,.,.1.4 ,.,.2.2.1 ASTM:2 D 217 D 4175,2.2 :3 IP 50 3.3.1:3.1.1 ,2 ASTM,ASTM www.astm.org ASTM serviceastm.org.ASTM.Document Summary ASTM.3 :61 New Cavendish St.,London,WIG 7AR,U.K.,http:/www.energyinst.org.uk.ASTM D 1403-10 3 .3.1.1.1 .D 217 3.1.2 ,.D 4175 3.1.3 ,.3.1.3.1 .,.D 217 3.1.4 ,.3.1.4.1 1/4 (Al.l)1/2 (A1.3).3.1.5 ,.3.1.5.1 (,)(,),.:,ASTM D 1403-10 4 .D 217 3.2 :3.2.1 ,0,1,1/4 1/2 5.3.2.1.1 ,D 217.-,.3.2.2 ,.1 D 217,1/4 1/2 .3.2.3 25C(77F)1/4 1/2 .3.2.4 ,25C(77F),60 1/4 1/2 .3.2.5 1/4 1/2 .4.4.1 25 0,5C(77 1F)1/4 1/2 ,5 0,1.ASTM D 1403-10 5 5.5.1 (NLGI)0 4 D 217.5.2 .(.9 10).,D 217.5.3 ,NLGI.,.5.4 .6.6.1 ,.1 D 217,1/4 1/2 .1 .,.6.2 1/4 ,Al.l.6.3 1/4 ,A1.2.ASTM D 1403-10 6 6.4 1/2 ,A1.3.6.5 1/2 ,A1.4.6.6 ,25 0,5C(77 1F).,.,.,.6.2,13 (0,5).7.7.1 .,.7.2 ,25 0,5C(77 1F),25 0,5C(77 1F).,ASTM D 1403-10 7 .,.,.,45 ,.,.2 ,.,.3 ,.,.7.3 .,.,.,.7.4 ,.,.ASTM D 1403-10 8 .5,0 0,1.,(0,1).4 ,.7.5 ,.,(7.2).,7.2.,7.3.0,1,1/4 1/2 .8.8.1 .8.2 ,7 (0,25),.,.25 0,5C(77 1F),ASTM D 1403-10 9 25 0,5C(77 1F).,.60 1 5 .,.,.8.3 8.4.5 ,.8.3 ,.,.,45 ,.6 ,.,60 .1 ()1/4 1/2 2 4 3 4 ASTM D 1403-10 10 7 ,.,.8.4 ,7.3,7.4 7.5.0,1,1/4 1/2 .9.9.1 ,(7.5),(D 217):9.1.1 1/4 :(1):P-D 217,p-1/4 9.1.2 1/2 :(2):P-D 217,r-1/2 .8 ,1/4 1/2 ,D 217.,1/4 1/2 ,.ASTM D 1403-10 11 10.10.1 1/4 1/2 ().9.1.1 9.1.2.11.4 11.1 D02,(RR:D02-1007).,:11.1.1 ,1 .2 ()1/4 1/2 21 16 18 18 11.1.2 ,2 .11.2 4 -ASTM International RR:D02-1689.ASTM D 1403-10 12 ,.12.12.1 1/4 ;1/2 ;ASTM D 1403-10 13 ()A1.A1.1 45 50 ,.A1.1.9,38 0,025.A1.2 ,.A1.2.60 10 ,14 (9/16).A1.3 ,45 50 ,.A1.3.37,5 0,050.22,5 0,025.15 0,025.A1.4 ,.A1.4.ASTM D 1403-10 14 60 10 ,35 (13/8).1/64 (0,4).A1.1 45/50 =9,38 0,025 ASTM D 1403-10 15 .1/64 (0,4).A1.2 8 .1/8,1/2 .-1/4 -.3/4,11/16,1/8.=3,82 3 ASTM D 1403-10 16 .A1.3 =22,5 0.025 =15 0.025 =37,5 0,050 45/50 ASTM D 1403-10 17 ,.1/64 (0,4).A1.4 8 .1/4 .ASTM D 1403-10 18 D02.G0 (D 1403-02(2007),.(1).6.6 .(2)2,.7.4.1 .8.5.(3).7.1,7.2,7.5 ,.(4)2 3,.(5).8.2 .8.4 .(6).11.1,.(7)1,.ASTM D 1403-10 19 ASTM International -,.,.,.-ASTM International.,.,.ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.610-832-9585,610-832-9555 E-mail:serviceastm.org ASTM:(www.astm.org).ASTM(www.astm.org/COPYRIGHT/).