ASTM_D_2235_-_22.pdf

Designation:D223522An American National StandardStandard Specification forSolvent Cement for Acrylonitrile-Butadiene-Styrene(ABS)Plastic Pipe and Fittings1This standard is issued under the fixed designation D2235;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers solvent cement for joiningacrylonitrile-butadiene styrene(ABS)plastic pipe and fittingsfor pressure and nonpressure systems.1.2 Recommendation for using solvent cement for joiningacrylonitrile-butadiene-styrene(ABS)plastic pipe and fittingsis given in Appendix X1.Satisfactory joining of pipe andfittings cannot be made in the presence of water,as waterdestroys the bonding ability of solvent cement;therefore,allmaterials must be dry for satisfactory joining.1.3 The text of this specification references notes,footnotes,and appendixes which provide explanatory material.Thesenotes and footnotes(excluding those in tables and figures)shallnot be considered as requirements of the specification.1.4 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 The following safety hazards caveat pertains only to thetest methods portion,Section 7,of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety,health,andenvironmental practices and determine the applicability ofregulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D329 Specification for AcetoneD618 Practice for Conditioning Plastics for TestingD740 Specification for Methyl Ethyl KetoneD883 Terminology Relating to PlasticsD1084 Test Methods for Viscosity of AdhesivesD1527 Specification for Acrylonitrile-Butadiene-Styrene(ABS)Plastic Pipe,Schedules 40 and 80(Withdrawn2013)3D2282 Specification for Acrylonitrile-Butadiene-Styrene(ABS)Plastic Pipe(Withdrawn 2006)3D2465 Specification for Threaded Acrylonitrile-Butadiene-Styrene(ABS)Plastic Pipe Fittings,Schedule 80(With-drawn 1985)3D2468 Specification for Acrylonitrile-Butadiene-Styrene(ABS)Plastic Pipe Fittings,Schedule 40(Withdrawn2003)3D2469 SpecificationforSocket-TypeAcrylonitrile-Butadiene-Styrene(ABS)Plastic Pipe Fittings,Schedule80(Withdrawn 1985)3D2661 Specification for Acrylonitrile-Butadiene-Styrene(ABS)Schedule 40 Plastic Drain,Waste,and Vent Pipeand FittingsD2680 Specification for Acrylonitrile-Butadiene-Styrene(ABS)and Poly(Vinyl Chloride)(PVC)Composite SewerPipingD2750 Specification for Acrylonitrile-Butadiene-Styrene(ABS)Plastics Utilities Conduit and Fittings(Withdrawn1997)3D2751 Specification for Acrylonitrile-Butadiene-Styrene(ABS)Sewer Pipe and Fittings(Withdrawn 2014)3D1600 Terminology forAbbreviated Terms Relating to Plas-tics1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.20 on Joining.Current edition approved July 1,2022.Published July 2022.Originally approvedin 1963.Last previous edition approved 2021 as D2235 21.DOI:10.1520/D2235-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1D3965 Classification System and Basis for Specifications forRigid Acrylonitrile-Butadiene-Styrene(ABS)Materialsfor Pipe and FittingsF402 Practice for Safe Handling of Solvent Cements,Primers,and Cleaners Used for Joining ThermoplasticPipe and FittingsF409 Specification for Thermoplastic Accessible and Re-placeable Plastic Tube and Tubular FittingsF412 Terminology Relating to Plastic Piping SystemsF493 Specifica