分享
ASTM_D_2200_-_13.pdf
下载文档

ID:181621

大小:69.02KB

页数:3页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_2200_ _13
Designation:D220013Swedish Standards AssociationStandard SIS 05 59 00ISO 8501SSPC:The Society for Protective CoatingsSSPC VIS 1,VIS 3,VIS 4/NACE VIS 7,VIS 5/NACE VIS 9Danish Standards AssociationDanish Standard DS 2019European Committee of Paint and PrintingInk Manufacturers AssociationStandard Practice forUse of Pictorial Surface Preparation Standards and Guidesfor Painting Steel Surfaces1This standard is issued under the fixed designation D2200;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope1.1 The visual surface preparation guides and standardsconsist of a series of color prints available as separatepublications.Five different sets of photographs are described inthis standard,designated as Method A(ISO/Swedish Stan-dard2)and Methods B through E(SSPC Guides and ReferencePhotographs3).The methods differ in the depiction of the initialsurface,in the definition and depiction of the cleaningconditions,and in the number of cleaning methods included.Because of these differences,the specifier should state whichmethod to use.1.2 The colored visual surface preparation guides representdifferent conditions of hot rolled carbon steel before and aftersurface preparation.Prior to cleaning,there are four rustgrades,A to D,that cover the range from intact mill scale to100%rusted and pitted steel.The standards then depict theappearance of the initial conditions after cleaning by one ormore methods(for example,dry abrasive blast cleaning)tovarious degrees of thoroughness.In addition,Method Bincludes three painted conditions that contain various degreesof deterioration.The Guide3depicts these conditions aftervarious degrees of dry abrasive blast cleaning.Method Cincludes four rust grades and three painted conditions thatcontain various degrees of deterioration.The Guide4depictsthese conditions after various degrees of hand and power toolcleaning.Method D includes two rust grades and four paintedconditions that contain various degrees of deterioration.TheGuide5depicts these conditions after various degrees of waterjetting,with three levels of flash rusting.Method E includestwo rust grades.The Guide6depicts these conditions aftervarious degrees of wet abrasive blast cleaning,with threelevels of flash rusting.2.Referenced Documents2.1 Other Documents:Pictorial Surface Preparation Standards and Guides2,3,4,5,6Surface Cleanliness Definitions3,43.Terminology3.1 Definitions:3.1.1 The cleanliness definitions for the Method A visualsurface preparation standard appear in the text of the pictorialsurface preparation standards publication.2The definitions forMethods B,C,D,and E are found in a separate publication.3,4,5,64.Significance and Use4.1 The appearance of the various degrees of dry and wetabrasive blast cleaning,hand and power tool cleaning and1This practice is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.46 on Industrial Protective Coatings.The pictorial standards described were prepared by the Swedish CorrosionInstitute and have been jointly approved by ASTM,The Society For ProtectiveCoatings(SSPC)(VIS 1),and the Swedish Standardizing Commission.Current edition approved June 1,2013.Published July 2013.Originally approvedin 1966.Last previous edition approved in 2008 as D2200 08.DOI:10.1520/D2200-13.2The pictorial surface preparation standard Method A is available from TheSociety for Protective Coatings(SSPC),40 24th St.,6th Floor,Pittsburgh,PA15222-4656,http:/www.sspc.org and Sveriges Standardiseringskommission,Box3295,Stockholm 3,Sweden.3The Visual Guide for Method B and surface cleanliness definitions are availablefrom The Society for Protective Coatings(SSPC),40 24th St.,6th Floor,Pittsburgh,PA 15222-4656,http:/www.sspc.org.4The Visual Guide for Method C and the surface cleanliness definitions areavailable from The Society for Protective Coatings(SSPC),40 24th St.,6th Floor,Pittsburgh,PA 15222-4656,http:/www.sspc.org.5The Visual Guide for Method D and the surface cleanliness definitions areavailable from The Society for Protective Coatings(SSPC),40 24th St.,6th Floor,Pittsburgh,PA 15222-4656,http:/www.sspc.org.6The Visual Guide for Method E and the surface cleanliness definitions areavailable from The Society for Protective Coatings(SSPC),40 24th St.,6th Floor,Pittsburgh,PA 15222-4656,http:/www.sspc.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 water jetting are influenced by the initial rust grades of the steelbeing cleaned and/or the type and condition of the coating onthe existing steel.The standards and guides aid visu

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开