温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_2859_
_16
Designation:D285916An American National StandardStandard Test Method forIgnition Characteristics of Finished Textile Floor CoveringMaterials1This standard is issued under the fixed designation D2859;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This fire-test-response standard describes a test methodfor the determination of the flammability of finished textilefloor covering materials when exposed to an ignition sourceunder controlled laboratory conditions.1.1.1 Carpets and rugs offered for sale in the United Statesare required by the Consumer Product Safety Commission(CPSC)to comply with the test methods in 16 CFR 1630 or 16CFR 1631,as appropriate.1.1.2 This test method is similar but not identical to the testmethods contained in 16 CFR 1630 and CFR 1631 and issuedby CPSC.If compliance with one of the CPSC test methods isrequired,this test method does not ensure regulatory compli-ance.1.2 This test method is applicable to all types of textile floorcoverings,regardless of the method of fabrication or whetherthey are made from natural or man-made fibers.It is possibleto apply this test method to unfinished material;however,theresults of such a test shall not be considered a satisfactoryevaluation of a textile floor covering material for ultimateconsumer use.1.3 The values stated in SI units are to be regarded as thestandard.The values given in brackets are for information only.1.4 This standard is used to measure and describe theresponse of materials,products,or assemblies to heat andflame under controlled conditions,but does not by itselfincorporate all factors required for fire hazard or fire riskassessment of the materials,products,or assemblies underactual fire conditions.1.5 Fire testing of products and materials is inherentlyhazardous,and adequate safeguards for personnel and propertyshall be employed in conducting these tests1.6 The text of this standard references notes and footnoteswhich provide explanatory material.These notes and footnotes(excluding those in tables and figures)shall not be consideredas requirements of the standard.1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2C1186 Specification for Flat Fiber-Cement SheetsD123 Terminology Relating to TextilesD1776 Practice for Conditioning and Testing TextilesD5684 Terminology Relating to Pile Floor CoveringsE176 Terminology of Fire Standards2.2 AATCC Standard:Method 138-2014,Shampooing:Washing of Textile FloorCoverings32.3 U.S.Consumer Product Safety Commission:416 CFR Part 1630 Standard for the surface flammability ofcarpets and rugs(FF 1-70)16 CFR Part 1631 Standard for the surface flammability ofsmall carpets and rugs(FF 2-70)3.Terminology3.1 Definitions:3.1.1 For definitions of terms contained in this test methodassociated with fire issues refer to Terminology E176.Fordefinitions of terms contained in this test method and associ-ated with textile issues refer to Terminology D123.For1This test method is under the jurisdiction of ASTM Committee E05 on FireStandards and is direct responsibility of Subcommittee E05.22 on Surface Burning.Current edition approved June 1,2016.Published July 2016.Originally approvedin 1970.Last previous edition approved in 2015 as D2859-15.DOI:10.1520/D2859-16.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Technical Manual of the American Association of Textile Chemists andColorists(AATCC),P.O.Box 12215,Research Triangle Park,NC 27709,http:/www.aatcc.org.4Can be found in Title 16,Volume 2 of the Code of Federal Regulations.Available from U.S.Government Printing Office Superintendent of Documents,732N.Capitol St.,NW,Mail Stop:SDE,Washington,DC 20401.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 definitions of terms contained in this test method and associ-ated with pile floor covering issues refer to TerminologyD5684.3.2 Definitions of Terms Specific to This Standard:3.2.1 finished,adjin textile floor covering materials,thecompletion of all manufacturing operations.3.2.2 flammability,nthe capability of burning with a flameunder specified conditions(see Terminology E176 for addi-tional discussion o