ASTM_D_4116_-_20.pdf

Designation:D411620Standard Performance Specification forWomens and Girls Knitted and Woven Corset-Girdle-Combination Fabrics1This standard is issued under the fixed designation D4116;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This performance specification covers woven and knit-ted fabrics composed of any textile fiber or mixture of fibersused in corsets,girdles or a combination of the same.1.2 This performance specification is not applicable toknitted or woven corset-girdle-combination fabrics,to knittedlace fabrics,and to fabrics used for interlinings.1.3 These requirements apply to the length and widthdirections for those properties where each fabric direction ispertinent.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD434 Test Method for Resistance to Slippage of Yarns inWoven Fabrics Using a Standard Seam(Withdrawn2003)3D2261 Test Method for Tearing Strength of Fabrics by theTongue(Single Rip)Procedure(Constant-Rate-of-Extension Tensile Testing Machine)D2262 Test Method for Tearing Strength of Woven Fabricsby the Tongue(Single Rip)Method(Constant-Rate-of-Traverse Tensile Testing Machine)(Withdrawn 1995)3D3786 Test Method for Bursting Strength of TextileFabricsDiaphragm Bursting Strength Tester MethodD3787 Test Method for Bursting Strength of TextilesConstant-Rate-of-Traverse(CRT)Ball Burst TestD5034 Test Method for Breaking Strength and Elongation ofTextile Fabrics(Grab Test)D7022 Terminology Relating to Apparel2.2 AATCC Test Methods:4TM8 Colorfastness to Crocking:Crockmeter MethodTM15 Colorfastness to PerspirationTM16.3 Colorfastness to Light:Xenon-ArcTM23 Colorfastness to Burnt Gas FumesTM61 Colorfastness to Laundering:AcceleratedTM116 Colorfastness to Crocking:Rotary Vertical Crock-meter MethodTM135 Dimensional Changes of Fabrics after Home Laun-deringTM172 Colorfastness to Powdered Non-Chlorine Bleach inHome LaunderingTM188 Colorfastness to Sodium Hypochlorite Bleach inHome LaunderingEP1 Gray Scale for Color ChangeEP2 Gray Scale for StainingEP8 AATCC 9-Step Chromatic Transference ScaleM11 A Glossary of AATCC Standard Terminology2.3 Federal Standard:516 CFR 1610,Chapter II-Consumer Product Safety Com-mission Subchapter D-Flammable Fabrics Act Regula-tions2.4 Military Standard:6MIL-STD-105D Sampling Procedures and Tables for In-spection by Attributes1This performance specification is under the jurisdiction of ASTM CommitteeD13 on Textiles and is the direct responsibility of Subcommittee D13.61 onApparel.Current edition approved Feb.1,2020.Published February 2020.Originallyapproved in 1982.Last previous edition approved in 2014 as D4116 14.DOI:10.1520/D4116-20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American Association of Textile Chemists and Colorists(AATCC),P.O.Box 12215,Research Triangle Park,NC 27709,http:/www.aatcc.org.5Available from Superintendent of Documents,Government Printing Office,Washington,DC 20402.6Available from Standardization Documents Order Desk,Bldg.4 Section D,700Robbins Ave.,Philadelphia,PA 19111-5094,Attn:NPODS.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 Copyright by ASTM Intl(all rights reserved);Tue Feb 25 21:40:51 EST 2020Downloaded/printed byPurdue University Libraries(Purdue University Libraries)pursuant to License Agreement.No further reproductions authorized.NOTE1Reference to test methods in this standard give only thepermanent part of the designation of ASTM,AATCC,or other testmethods.The current editions of each te