分享
ASTM_D_4172_-_18.pdf
下载文档

ID:181260

大小:191.02KB

页数:5页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_4172_ _18
Designation:D417218Standard Test Method forWear Preventive Characteristics of Lubricating Fluid(Four-Ball Method)1This standard is issued under the fixed designation D4172;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This test method covers a procedure for making apreliminary evaluation of the anti-wear properties of fluidlubricants in sliding contact by means of the Four-Ball WearTest Machine.Evaluation of lubricating grease using the samemachine is detailed in Test Method D2266.1.2 The values stated in SI units are to be regarded asstandard.Because the equipment used in this test method isonly available in kgf units,SI units in parentheses are forinformation only.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D2266 Test Method for Wear Preventive Characteristics ofLubricating Grease(Four-Ball Method)2.2 ANSI Standard:3B3.12 Specification for Metal Balls3.Terminology3.1 Definitions:3.1.1 lubricant,nany material interposed between twosurfaces that reduces the friction or wear between them.3.1.2 wear,ndamage to a solid surface,generally involv-ing progressive loss of material due to relative motion betweenthat surface and a contacting substance or surface.4.Summary of Test Method4.1 Three 12.7 mm(12in.)diameter steel balls are clampedtogether and covered with the lubricant to be evaluated.Afourth 12.7 mm diameter steel ball,referred to as the top ball,is pressed with a force of 15 kgf or 40 kgf(147 N or 392 N)into the cavity formed by the three clamped balls for three-point contact.The temperature of the test lubricant is regulatedat 75 C(167 F)and then the top ball is rotated at 1200 r/minfor 60 min.Lubricants are compared by using the average sizeof the scar diameters worn on the three lower clamped balls.NOTE1Because of differences in the construction of the variousmachines on which the four-ball test can be made,the manufacturersinstructions should be consulted for proper machine set up and operation.NOTE2Although the test can be run under other parameters,theprecision noted in Section 10 may vary.No aqueous fluid was included inthe round-robin to establish the precision limits.5.Significance and Use5.1 This test method can be used to determine the relativewear preventive properties of lubricating fluids in slidingcontact under the prescribed test conditions.No attempt hasbeen made to correlate this test with balls in rolling contact.The user of this test method should determine to his own1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricantsand is the direct responsibility ofSubcommittee D02.L0.11 on Tribological Properties of Industrial Fluids andLubricates.Current edition approved Oct.1,2018.Published October 2018.Originallyapproved in 1982.Last previous edition approved in 2016 as D4172 94(2016).DOI:10.1520/D4172-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 satisfaction whether results of this test procedure correlate withfield performance or other bench test machines.6.Apparatus6.1 Four-Ball Wear Test Machine4See Figs.1-3.NOTE3It is important to distinguish between the Four-Ball E.P.andthe Four-Ball Wear Test Machines.The Four-Ball E.P.Test Machine isdesigned for testing under heavier loads and lacks the sensitivity

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开