ASTM_D_2890_-_92_2018.pdf

Designation:D289092(Reapproved 2018)Standard Test Method forCalculation of Liquid Heat Capacity of Petroleum DistillateFuels1This standard is issued under the fixed designation D2890;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the calculation of liquid heatcapacity,Btu/lb F(kJ/kg K),at atmospheric pressure,ofpetroleum fuels for which distillation data may be obtained inaccordance with Test Method D86 without reaching a decom-position point prior to obtaining 90%by volume distilled.1.2 This test method is not applicable at temperatures lessthan 0 F(18 C)and greater than 60 F(16 C)above thevolumetric average boiling point of the fuel.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D86 Test Method for Distillation of Petroleum Products andLiquid Fuels at Atmospheric PressureD287 Test Method for API Gravity of Crude Petroleum andPetroleum Products(Hydrometer Method)3.Summary of Test Method3.1 The Watson characterization factor,K,is obtained froma graphical correlation relating determined Test Method D86distillation data and K.The liquid heat capacity is obtained,either graphically or mathematically,from correlations relatingcalculated heat capacity,temperature at which heat capacity isbeing calculated,determined API gravity,and K.NOTE1Details of the method have been published.34.Significance and Use4.1 Heat capacities obtained by this method are those atatmospheric pressure.However,because the temperature rangeis low,the calculated values are similar to saturated liquid heatcapacities in the temperature-pressure range required for mostengineering design.5.Data Requirements5.1 Distillation temperatures at(in F)10%,30%,50%,70%,and 90%by volume distilled obtained in accordancewith Test Method D86.5.2 API gravity determined in accordance with Test MethodD287 or a method of equivalent accuracy.6.Procedure6.1 Calculate to the nearest 0.1 unit the slope of the TestMethod D86 distillation curve,F/volume%,as the differencebetween the 10 and 90 volume%distilled temperatures di-vided by 80.6.2 Calculate to the nearest 1 F the volumetric averageboiling point(VABP)as the sum of Test Method D86 10%,30%,50%,70%,and 90%by volume distilled temperaturesdivided by 5.6.3 Obtain a temperature correction to the nearest 1 F fromFig.1,using the slope and VABPcalculated in accordance with6.1 and 6.2.Calculate the mean average boiling point(Me-ABP)as the VABP plus the correction.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.04.0K on Correlative Methods.Current edition approved Oct.1,2018.Published November 2018.Originallyapproved in 1970.Last previous edition approved in 2013 as D2890 92(2013).DOI:10.1520/D2890-92R18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Technical Data Book-Petroleum Refining,Chapter 7,American PetroleumInstitute,Division of Refining,1220 L St.NW,Washington,DC 20005.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 6.4 Obtain to the nearest 0.1 unit the Watson characteriza-tion factor,K,from Fig.2 using the determined API gravityand calculated MeABP.6.5 Obtain the calculated heat capacity at each specifiedtemperature,either graphically from Fig.3 or by solving thefollowing equation:Cp50.68112 0.308 G10.0008152 0.000306 G!T#(1)0.055 K10.35!where:Cp=heat ca