ASTM_D_3142_-_D_3142M_-_17.pdf

Designation:D3142/D3142M17Standard Test Method forSpecific Gravity,API Gravity,or Density of Cutback Asphaltsby Hydrometer Method1This standard is issued under the fixed designation D3142/D3142M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the laboratory determination,using a glass hydrometer,of the density,specific gravity,orAPI gravity of cutback asphalts as defined in SpecificationsD2026,D2027,and D2028(Note 1).Values are measured on ahydrometer at convenient temperatures,readings of density,specific gravity,and API gravity being reduced to 15 C or60 F by means of international standard tables.By means ofthese same tables,values determined in one of the threesystems of measurement are convertible to equivalent values ineither system so that measurements may be made in the unitsof local convenience.NOTE1This test method is applicable to cutback asphalts and ingeneral follows,but provides more explicit routines than,the procedureoutlined in Test Method D1298.1.2 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard.Thevalues stated in each system may not be exact equivalents;therefore,each system shall be used independently of the other.Combining values from the two systems may result in noncon-formance with the standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.Specific precautionary statements are given in Section 7.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C670 Practice for Preparing Precision and Bias Statementsfor Test Methods for Construction MaterialsD140 Practice for Sampling Bituminous MaterialsD1250 Guide for Use of the Petroleum Measurement TablesD1298 Test Method for Density,Relative Density,or APIGravity of Crude Petroleum and Liquid Petroleum Prod-ucts by Hydrometer MethodD2026 Specification for Cutback Asphalt(Slow-CuringType)D2027 Specification for Cutback Asphalt(Medium-CuringType)D2028 Specification for Cutback Asphalt(Rapid-CuringType)E1 Specification for ASTM Liquid-in-Glass ThermometersE100 Specification for ASTM Hydrometers3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 API gravitya function of specific gravity 15/15 C60/60 F,represented by the equation:API5141.5/SG 15/15C#2 131.5 orAPI5141.5/SG 60/60F#2 131.5No statement of reference temperature is required since15 C 60 F is included in the definition.3.1.2 densitythe mass of material per unit volume.Whenreporting results,explicitly state the density in units of mass(kilograms)and volume(litres),together with the standardreference temperature.3.1.3 observed valuesvalues observed at temperaturesother than the standard reference temperature.Values observedat other temperatures are only hydrometer readings,and notdensity,relative density(specific gravity),or API gravity.3.1.4 specific gravitythe ratio of mass of a given volumeof a material at a specified temperature to the mass of an equal1This test method is under the jurisdiction of ASTM Committee D04 on Roadand Paving Materials and is the direct responsibility of Subcommittee D04.47 onMiscellaneous Asphalt Tests.Current edition approved Dec.15,2017.Published January 2018.Originallyapproved in 1972.Last previous edition approved in 2011 as D3142/D3142M 11.DOI:10.1520/D3142/D3142M-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 volume of pure water measured at the reference temperature.When reporting results,the standard reference temperaturemust be stated.4.Summary of Test Method4.1 The sample is brought to the testing temperature andtransferred to a hydrometer cylinder at