ASTM_D_3105_-_17.pdf

Designation:D310517Standard Index of Methods forTesting Elastomeric and Plastomeric Roofing andWaterproofing Materials1This standard is issued under the fixed designation D3105;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This index is provided for reference to aid in theselection of procedures and test methods used in the evaluationof sheet and liquid roofing materials,as appropriate.Compo-sition specifications and analytical methods in general,as wellas tests on raw materials,are not included,the scope beinglimited to procedures used in the evaluation of the materials asreceived or as finished materials or coatings.2.Referenced Documents2.1 ASTM Standards:2D92 Test Method for Flash and Fire Points by ClevelandOpen Cup TesterD93 Test Methods for Flash Point by Pensky-MartensClosed Cup TesterD146/D146M Test Methods for Sampling and TestingBitumen-Saturated Felts and Woven Fabrics for Roofingand WaterproofingD228/D228M Test Methods for Sampling,Testing,andAnalysis of Asphalt Roll Roofing,Cap Sheets,andShingles Used in Roofing and WaterproofingD412 Test Methods for Vulcanized Rubber and Thermoplas-tic ElastomersTensionD413 Test Methods for Rubber PropertyAdhesion to Flex-ible SubstrateD430 Test Methods for Rubber DeteriorationDynamicFatigueD471 Test Method for Rubber PropertyEffect of LiquidsD543 Practices for Evaluating the Resistance of Plastics toChemical ReagentsD570 Test Method for Water Absorption of PlasticsD573 Test Method for RubberDeterioration in an AirOvenD624 Test Method for Tear Strength of Conventional Vul-canized Rubber and Thermoplastic ElastomersD638 Test Method for Tensile Properties of PlasticsD696 Test Method for Coefficient of Linear Thermal Expan-sion of Plastics Between 30C and 30C with a VitreousSilica DilatometerD746 Test Method for Brittleness Temperature of Plasticsand Elastomers by ImpactD750 Practice for Rubber Deterioration Using ArtificialWeathering ApparatusD751 Test Methods for Coated FabricsD816 Test Methods for Rubber CementsD823 Practices for Producing Films of Uniform Thicknessof Paint,Varnish,and Related Products on Test PanelsD882 Test Method for Tensile Properties of Thin PlasticSheetingD1002 Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Ten-sion Loading(Metal-to-Metal)D1004 Test Method for Tear Resistance(Graves Tear)ofPlastic Film and SheetingD1042 Test Method for Linear Dimensional Changes ofPlastics Caused by Exposure to Heat and MoistureD1149 Test Methods for Rubber DeteriorationCracking inan Ozone Controlled EnvironmentD1203 Test Methods for Volatile Loss From Plastics UsingActivated Carbon MethodsD1204 Test Method for Linear Dimensional Changes ofNonrigid Thermoplastic Sheeting or Film at ElevatedTemperatureD1239 Test Method for Resistance of Plastic Films toExtraction by ChemicalsD1310 Test Method for Flash Point and Fire Point of Liquidsby Tag Open-Cup ApparatusD1475 Test Method For Density of Liquid Coatings,Inks,and Related ProductsD1499 Practice for Filtered Open-Flame Carbon-Arc Expo-sures of PlasticsD1640/D1640M Test Methods for Drying,Curing,or FilmFormation of Organic CoatingsD1653 Test Methods for Water Vapor Transmission of Or-ganic Coating Films1This index of methods is under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.01on Nomenclature,Definitions and Editorial.Current edition approved Jan.1,2017.Published February 2017.Originallyapproved in 1972.Last previous edition approved in 2008 as D3105 08.DOI:10.1520/D3105-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 D1709 Test Methods for Impact Resistance of Plastic Filmby the Free-Falling Dart MethodD1790 Test Method for Brittleness Temperature of PlasticSheeting by ImpactD1824 Test Method for Apparent Viscosity of Plastisols andOrganosols at Low Shear RatesD1922 Test Method for Propagation Tear Resistance ofPlastic Film and Thin Sheeting by Pendulum MethodD2136 Test Method for Coated FabricsLow-TemperatureBend TestD2137 Test Methods for Rubber PropertyBrittleness Pointof Flexible Polymers and Coated FabricsD2196 Test Meth