ASTM_D_2672_-_14.pdf

Designation:D267214Standard Specification forJoints for IPS PVC Pipe Using Solvent Cement1This standard is issued under the fixed designation D2672;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification covers the socket produced for sol-vent cement joints on both pressure and non-pressure IPS pipe.It also covers the testing of the joints on both pressure andnon-pressure pipe,and includes requirements for socketdimensions,burst pressure,and joint tightness tests of thesolvent cemented joints.The tests described are not intendedfor routine quality control,but rather to evaluate the perfor-mance characteristics of the joint.NOTE1On dual marked Schedule 40 DWV and potable water pipe,the socket bells must conform to the dimensional and physical require-ments for pressure socket bells.1.2 The text of this specification references notes,footnotes,and appendixes which provide explanatory material.Thesenotes and footnotes(excluding those in tables and figures)shallnot be considered as requirements of the specification.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.NOTE2Changes in ground,water,or air temperature will produceexpansion or contraction forces in PVC piping,and these will result inlongitudinal shear stresses in the solvent cement joints.These stressesmust be considered in the design and operation of the system.NOTE3See Practice D618 for information relating to this specifica-tion.1.4 The following safety hazards caveat pertains only to thetest method portion,Section 10,of this specification.Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1599 Test Method for Resistance to Short-Time HydraulicPressure of Plastic Pipe,Tubing,and FittingsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1785 Specification for Poly(Vinyl Chloride)(PVC)PlasticPipe,Schedules 40,80,and 120D2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2241 Specification for Poly(Vinyl Chloride)(PVC)Pressure-Rated Pipe(SDR Series)D2565 Practice for Xenon-Arc Exposure of Plastics In-tended for Outdoor ApplicationsD2665 Specification for Poly(Vinyl Chloride)(PVC)PlasticDrain,Waste,and Vent Pipe and FittingsD2855 Practice for Making Solvent-Cemented Joints withPoly(Vinyl Chloride)(PVC)Pipe and FittingsF412 Terminology Relating to Plastic Piping SystemsF512 Specification for Smooth-Wall Poly(Vinyl Chloride)(PVC)Conduit and Fittings for Underground InstallationF656 Specification for Primers for Use in Solvent CementJoints of Poly(Vinyl Chloride)(PVC)Plastic Pipe andFittings2.2 NSF Standard:Standard No.14 for Plastic Piping Components and RelatedMaterials33.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F412 and abbreviations are in accordance with Termi-nology D1600,unless otherwise specified.1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.20 on Joining.Current edition approved Nov.15,2014.Published February 2015.Originallyapproved in 1968.Last previous edition approved in 2009 as D2672 96a(2009).DOI:10.1520/D2672-14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from NSF International,P.O.Box 130140,789 N.Dixboro Rd.,AnnArbor,MI 48113-0140,http:/www.nsf.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.Materials4.1 GeneralPVC plastics used to make the pipe,which arebelled under this specification,are designated in PVC productstandards referencing this standard.4.2 Solvent cements must conform to the requirements ofSpecification D2565.4.3 Primers must conform to the requirements of Specifica-tion F656.5.Requirements5.1 Bell Socket Dimensions and Tolerances:5.1.1 Diameters and LengthThe diameter,lengths,andtolerances of the bell sockets shall be as shown in Table 1 whenmeasured in accordance with Test Method D2122.5.1.2 Wall Thicknesse