分享
ASTM_D_2354_-_10e1.pdf
下载文档

ID:180644

大小:121.72KB

页数:3页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_2354_ _10e1
Designation:D2354101Standard Test Method forMinimum Film Formation Temperature(MFFT)of EmulsionVehicles1This standard is issued under the fixed designation D2354;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEFootnote 2 was corrected editorially in March 2013.1.Scope1.1 This test method covers the determination of the mini-mum temperature at which emulsion vehicles coalesce to formcontinuous films.The term“emulsion”in this test methodincludes latex vehicles.1.2 This test method is limited to emulsions having mini-mum film formation temperatures below 90C.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Summary of Test Method2.1 In this test method the minimum film formation tem-perature(MFFT)is determined by visual observation ofcracking or whitening in films that have dried over a substratehaving a controlled temperature gradient.3.Significance and Use3.1 The satisfactory film integrity of emulsion coatingsrequires that as the aqueous phase evaporates the resinousportion of the vehicle coalesces into a continuous film.Lowtemperature impairs the fluidity of the resin particle andthereby their ability to coalesce.Vehicles that can withstandlow temperatures are therefore required,and MFFT is animportant quality feature of emulsion vehicles.4.Apparatus4.1 Minimum Film Formation Temperature BarAn MFFTunit2such as is illustrated in Fig.1.The bar represented in Fig.1 is designed to be used with thermocouples.The thermo-couple leads used with the assembly are iron-constantan withan external resistance of 10.Also included is a pyrometer(not shown in Fig.1).NOTE1Thermometers can be used as an alternative way of measuringtemperature.3It is noted that larger holes(532in.)(4 mm)will have to bedrilled in the bar to accommodate the thermometers.If thermometers areselected,all holes are drilled on the same side of the bar,as opposed to thesystem of alternate placement of holes when using thermocouples.NOTE2Aself-contained unit eliminating the need for any accessories,such as for sub-ambient cooling or temperature measurement,andrequiring only an electrical outlet,piped water,and an air or nitrogensupply has been developed by ICI Paints Division.44.2 Dry Air or Dry Nitrogen Supply,with a regulating valveand flow meter.4.3 Film Caster,having a 6-mil(150-m)clearance.5.Reagents and Materials5.1 Dry Ice.5.2 Isopropanol,anhydrous.1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.33 on Polymers and Resins.Current edition approved July 1,2010.Published July 2010.Originally approvedin 1965.Last previous edition approved in 1998 as D2354 98 which waswithdrawn March 2007 and reinstated in July 2010.DOI:10.1520/D2354-10E01.2The sole source of supply of the MFFT bar,Model CS 188,known to thecommittee at this time is Dek-Tron Scientific Instrument Corp.,244 East 3rd Street,Plainfield,NJ 07060.If you are aware of alternative suppliers,please provide thisinformation to ASTM International.Your comments will receive careful consider-ation at a meeting of the responsible technical committee,1which you may attend.3The sole source of supply of the thermometer,Prince No.A-011044 known tothe committee at this time is Princo Instruments Inc.,1020 Industrial Hwy.,Southampton,PA 18966.If you are aware of alternative suppliers,please providethis information to ASTM International.Your comments will receive carefulconsideration at a meeting of the responsible technical committee,1which you mayattend.4The sole source of supply of the MFFTBAR units,Models MFFT-60,andMFFT-90,known to the committee at this time is Rhopoint Instrumentation Ltd.,Beeching Rd.,Bexhill-on-Sea,East Sussex,TN39 3LG,England.For the name ofa local distributor,telephone them at 011441424214291.Interested parties areinvited to submit information regarding the identification of acceptable alternativesto the Committee on Standards,ASTM International.Your comments will receivecareful consideration at a meeting of the responsible technical committee,1whichyou may attend.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.Procedure6.1 Set up the MFFT bar in a level position with the lowertemperature leg of the bar immer

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开