ASTM_D_2859_-_16_2021.pdf

Designation:D285916(Reapproved 2021)An American National StandardStandard Test Method forIgnition Characteristics of Finished Textile Floor CoveringMaterials1This standard is issued under the fixed designation D2859;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This fire-test-response standard describes a test methodfor the determination of the flammability of finished textilefloor covering materials when exposed to an ignition sourceunder controlled laboratory conditions.1.1.1 Carpets and rugs offered for sale in the United Statesare required by the Consumer Product Safety Commission(CPSC)to comply with the test methods in 16 CFR 1630 or 16CFR 1631,as appropriate.1.1.2 This test method is similar but not identical to the testmethods contained in 16 CFR 1630 and CFR 1631 and issuedby CPSC.If compliance with one of the CPSC test methods isrequired,this test method does not ensure regulatory compli-ance.1.2 This test method is applicable to all types of textile floorcoverings,regardless of the method of fabrication or whetherthey are made from natural or man-made fibers.It is possibleto apply this test method to unfinished material;however,theresults of such a test shall not be considered a satisfactoryevaluation of a textile floor covering material for ultimateconsumer use.1.3 The values stated in SI units are to be regarded asstandard.The values given in parentheses after SI units areprovided for information only and are not considered standard.1.4 This standard is used to measure and describe theresponse of materials,products,or assemblies to heat andflame under controlled conditions,but does not by itselfincorporate all factors required for fire hazard or fire riskassessment of the materials,products,or assemblies underactual fire conditions.1.5 Fire testing of products and materials is inherentlyhazardous,and adequate safeguards for personnel and propertyshall be employed in conducting these tests1.6 The text of this standard references notes and footnoteswhich provide explanatory material.These notes and footnotes(excluding those in tables and figures)shall not be consideredas requirements of the standard.1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C1186 Specification for Flat Fiber-Cement SheetsD123 Terminology Relating to TextilesD1776 Practice for Conditioning and Testing TextilesD5684 Terminology Relating to Pile Floor CoveringsE176 Terminology of Fire Standards2.2 AATCC Standard:Method 138-2014,Shampooing:Washing of Textile FloorCoverings32.3 U.S.Consumer Product Safety Commission:416 CFR Part 1630 Standard for the surface flammability ofcarpets and rugs(FF 1-70)16 CFR Part 1631 Standard for the surface flammability ofsmall carpets and rugs(FF 2-70)1This test method is under the jurisdiction of ASTM Committee E05 on FireStandards and is direct responsibility of Subcommittee E05.22 on Surface Burning.Current edition approved March 15,2021.Published March 2021.Originallyapproved in 1970.Last previous edition approved in 2016 as D2859-16.DOI:10.1520/D2859-16R21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Technical Manual of the American Association of Textile Chemists andColorists(AATCC),P.O.Box 12215,Research Triangle Park,NC 27709,http:/www.aatcc.org.4Can be found in Title 16,Volume 2 of the Code of Federal Regulations.Available from U.S.Government Printing Office Superintendent of Documents,732N.Capitol St.,NW,Mail Stop:SDE,Washington,DC 20401.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Orga