分享
ASTM_D_3928_-_00a_2018.pdf
下载文档

ID:179952

大小:86.40KB

页数:3页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_3928_ _00a_2018
Designation:D392800a(Reapproved 2018)Standard Test Method forEvaluation of Gloss or Sheen Uniformity1This standard is issued under the fixed designation D3928;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of the unifor-mity of gloss or sheen of a paint applied by brush to a test panelsimulating an interior wall section.Variations in gloss or sheenthat may be caused by short wet edge time,poor leveling,andpigment orientation or flotation during and after application areevaluated visually.1.2 Because both the application and the panel evaluationare very subjective,this test method should be used only forcomparative testing within one laboratory as the ratings as-signed by different laboratories do not usually agree(see 8.1).1.3 The values given in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Summary of Test Method2.1 Paint is brush applied to a test panel using proceduresand conditions that are most likely to cause nonuniformity ofgloss or sheen.The dry film is then viewed under conditionsthat accentuate variations in gloss or sheen and the overallappearance is evaluated.3.Significance and Use3.1 When coatings are applied to large flat surfaces such aswalls,the film thickness may vary or there may be small areasmissed entirely(holidays)when the color of the fresh materialand the previous film are very similar.It is much less costly ifthese areas can be touched up instead of having to repaint theentire surface.3.2 Thickness is also affected in the locations where an areacoated a short time before is joined with the area currentlybeing coated(laps).An application technique that may affectthe final appearance of the film is brushing or rolling thematerial in different directions in adjacent areas.3.3 Both buyers and sellers are interested in determiningwhether a coating can be applied without exhibiting areas thatdiffer in appearance because of laps and brush or roller marks,and whether it can be readily touched up to provide a uniformappearance in regard to gloss or sheen and all other aspects.4.Apparatus4.1 Paint Brush,250 mm(2 in.)wide with polyesterfilaments 70 mm(234in.)long,chisel tip 15 mm(916in.)thick.Previously used brushes are preferred.4.2 Paint Brush,25 mm(1 in.)wide with polyester fila-ments 57 mm(214in.)long,chisel tip 10 mm(716in.)thick.Previously used brushes are preferred.5.Reagents and Materials5.1 Laminated Fiber Board,610 by 300 mm(24 by 12 in.)with at least one smooth side.5.2 Latex-Base Primer.35.3 Control Paint(optional)Since there are no standardpanels,photographs,or paints for this test method,an agreed-upon paint of known uniformity of appearance should beincluded with the test paints as a control,unless the paints areonly ranked.1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.42 on Architectural Coatings.Current edition approved June 1,2018.Published June 2018.Originallyapproved in 1980.Last previous edition approved in 2014 as D3928 00a(2014).DOI:10.1520/D3928-00AR18.2The sole source of supply of a polyester brush No.B-20CS,known to thecommittee at this time is The Leneta Co.,15 Whitney Rd.,Mahwah,NJ 07430.Ifyou are aware of alternative suppliers,please provide this information to ASTMInternational Headquarters.Your comments will receive careful consideration at ameeting of the responsible technical committee,1which you may attend.3Similar to U.S.Federal Specification TT-P-650c Primer Coating Latex Base,White(for Gypsum Wallboard).Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 6.Procedure6.1 Apply the latex primer by spray to the entire f

此文档下载收益归作者所有

下载文档
猜你喜欢
你可能关注的文档
收起
展开