ASTM_D_3562_-_22.pdf

Designation:D356222Standard Performance Specification forWoven Drycleanable Coat Fabrics1This standard is issued under the fixed designation D3562;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This performance specification covers woven dryclean-able topcoats,overcoats,and dress coat outer fabrics composedof any textile fiber or mixture of textile fibers.1.2 This performance specification is not applicable towoven fabrics used for linings,interlinings,rainwear garments,and all-purpose,water-repellent garments nor is this perfor-mance specification applicable to bonded or laminated fabrics.1.3 These requirements apply to both the length and widthdirections for those properties where each fabric direction ispertinent.1.4 When a fabric requires special treatment,specific meth-ods will be described as they are developed for that material,and such special tests will have precedence over these generalrequirements.1.5 The following precautionary caveat pertains only to thetest method portion,Section 7,of this performance specifica-tion:This standard does not purport to address all of the safetyconcerns,if any,associated with its use.It is the responsibilityof the user of this standard to establish appropriate safety,health,and environmental practices and determine the appli-cability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD434 Test Method for Resistance to Slippage of Yarns inWoven Fabrics Using a Standard Seam(Withdrawn2003)3D1424 Test Method for Tearing Strength of Fabrics byFalling-Pendulum(Elmendorf-Type)ApparatusD2262 Test Method for Tearing Strength of Woven Fabricsby the Tongue(Single Rip)Method(Constant-Rate-of-Traverse Tensile Testing Machine)(Withdrawn 1995)3D2724 Test Method for Bond Strength of Bonded,Fused,and Laminated Apparel FabricsD5034 Test Method for Breaking Strength and Elongation ofTextile Fabrics(Grab Test)D7022 Terminology Relating to Apparel(Withdrawn 2022)32.2 AATCC Test Methods:4TM8 Colorfastness to Crocking:AATCC CrockmeterMethodTM15 Colorfastness to PerspirationTM16.3 Colorfastness to Light:Xenon-ArcTM23 Colorfastness to Burnt Gas FumesTM116 Colorfastness to Crocking:Rotary Vertical Crock-meter MethodTM124 Appearance of Durable Press Fabrics after RepeatedHome LaunderingsTM132 Colorfastness to DrycleaningTM135 Dimensional Changes in Automatic Home Launder-ing of Durable Press Woven or Knit FabricsEP1 Gray Scale for Color ChangeEP2 Gray Scale for StainingEP8 AATCC 9-Step Chromatic Transference Scale2.3 Federal Standard:516 CFR 1610 ChapterIIConsumerProductSafetyCommission,Subchapter DFlammable Fabrics ActRegulations2.4 ASQ Standard:ASQ Z1.4 Sampling Procedures and Tables for Inspectionby Attributes61This specification is under the jurisdiction of ASTM Committee D13 onTextiles and is the direct responsibility of Subcommittee D13.61 on Apparel.Current edition approved Nov.1,2022.Published November 2022.Originallyapproved in 1977.Last previous edition approved in 2014 as D3562 14.DOI:10.1520/D3562-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4AATCC Technical Manual,available from American Association of TextileChemists and Colorists(AATCC),One Davis Dr.,P.O.Box 12215,ResearchTriangle Park,NC 27709-2215.5Available from U.S.Government Printing Office Superintendent of Documents,732 N.Capitol St.,NW,Mail Stop:SDE,Washington,DC 20401.6Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1NOTE1Reference to test methods in this specification give only thepermanent part of the designation of ASTM,AATCC,or other testmethods.The current editions of each test method cited shall prevail.3.Terminology3.1 For all terminology re