ASTM_D_3622_-_11_2019.pdf

Designation:D362211(Reapproved 2019)Standard Specification for1-Propanol(n-Propyl Alcohol)1This standard is issued under the fixed designation D3622;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers n-propyl alcohol(1-propanol)for use in paint,varnish,lacquer,and related products.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 The following applies to all specified limits in thisstandard:for purposes of determining conformance with thisstandard,an observed value or a calculated value shall berounded off“to the nearest unit”in the last right-hand digitused in expressing the specification limit,in accordance withthe rounding-off method of Practice E29.1.4 For specific hazard information and guidance,see thesuppliers Material Safety Data Sheets for materials listed inthis specification.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D268 Guide for Sampling and Testing Volatile Solvents andChemical Intermediates for Use in Paint and RelatedCoatings and MaterialD1078 Test Method for Distillation Range of Volatile Or-ganic LiquidsD1209 Test Method for Color of Clear Liquids(Platinum-Cobalt Scale)D1296 Test Method for Odor of Volatile Solvents andDiluentsD1353 Test Method for Nonvolatile Matter in Volatile Sol-vents for Use in Paint,Varnish,Lacquer,and RelatedProductsD1364 Test Method for Water in Volatile Solvents(KarlFischer Reagent Titration Method)D1476 Test Method for Heptane Miscibility of LacquerSolventsD1613 Test Method for Acidity in Volatile Solvents andChemical Intermediates Used in Paint,Varnish,Lacquer,and Related ProductsD4052 Test Method for Density,Relative Density,and APIGravity of Liquids by Digital Density MeterD5386 Test Method for Color of Liquids Using TristimulusColorimetryE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE300 Practice for Sampling Industrial Chemicals2.2 U.S.Federal Specification:3PPP-C-2020 Chemicals,Liquid,Dry,and Paste:Packagingof3.Properties3.1 n-Propyl alcohol shall conform to the following require-ments:Apparent specific gravity:20/20 C0.804 to 0.807or25/25 C0.801 to 0.804Color,Pt-Co scale,maxA10Distillation rangeBNonvolatile matter,max,mg/100 mL5OdorCWater,max,weight%0.1DAcidity(free acid as acetic),max,weight%0.003EAInstrumental Pt-Co color determined by Test Method D5386 has been shown tohave no statistically significant difference from Pt-Co color determined by TestMethod D1209.However,it is not known whether 1-propyl alcohol was part of thesample set included in the interlaboratory study.BShall distill entirely within a 2 C range which shall include 97.2 C.COptional:Test for odor only when agreed upon as necessary between thesupplier and the customer.DThis quantitative water limit ensures miscibility without turbidity when 1 volumeis diluted with 19 volumes of 99%heptane at 20 C.1This specification is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.35 on Solvents,Plasticizers,and Chemical Intermediates.Current edition approved April 1,2019.Published April 2019.Originallyapproved in 1977.Last previous edition approved in 2011 as D3622 11.DOI:10.1520/D3622-11R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/www.dodssp.daps.mil.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 EEquivalent to 0.028 mg of KOH per gram of material.4.Sampling4.1 This material shall be sampled in accordance withPractice E300.5.Test Methods5.1 The properties enumerated in this specification shall bedetermined in accordance with the following ASTM methods.5.1.1 Apparent Specific GravityDetermine the apparent