分享
ASTM_D_2987_-_D_2987M_-_88_2019.pdf
下载文档

ID:179478

大小:72.13KB

页数:2页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_2987_ _D_2987M_ _88_2019
Designation:D2987/D2987M88(Reapproved 2019)Standard Test Method forMoisture Content of Asbestos Fiber1This standard is issued under the fixed designation D2987/D2987M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of the mois-ture content of asbestos fiber.1.2 WarningBreathing of asbestos dust is hazardous.Asbestos and asbestos products present demonstrated healthrisks for users and for those with whom they come into contact.In addition to other precautions,when working with asbestos-cement products,minimize the dust that results.For informa-tion on the safe use of chrysotile asbestos,refer to“Safe Use ofChrysotile:A Manual on Preventive and Control Measures.”21.3 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of whoever uses this standard to consult andestablish appropriate safety,health,and environmental prac-tices and determine the applicability of regulatory limitationsprior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D2590 Test Method for Sampling Chrysotile AsbestosD2946 Terminology for Asbestos and AsbestosCementProductsD3879 Test Method for Sampling Amphibole Asbestos(Withdrawn 2009)43.Summary of Test Method3.1 A weighed specimen of fiber is dried in an oven,cooledin a desiccator,and reweighed.The weight loss is used todetermine the percent moisture content of the fiber.4.Significance and Use4.1 This test method will give a value of moisture contentobtained under specified conditions.This value should not beconsidered as an absolute moisture content.Results may notcompare with those obtained by the same method underdifferent conditions,or by different methods.5.Apparatus5.1 Drying Oven,capable of maintaining 105 to 110C 220to 230F.5.2 Balance,with sensitivity of 0.01 g and capacity of atleast 400 g.5.3 Weighing ContainersShallow borosilicate glass dishesor corrosion-resistant metal pans approximately 200 mm 8 in.in diameter.Examples of suitable containers are glass culturedishes or sifting sieve pans.5.4 Desiccator.5.5 Timer,1 h.6.Sampling and Preparation6.1 Sampling and preparation shall be in accordance withTest Method D2590,omitting Section 6 of that test method,forchrysotile asbestos,and with Test Method D3879 omittingdrying step described in the first sentence of Section 6.3 of thelatter test method,for amphibole asbestos.When unsure of thetype of asbestos to be tested,refer to Terminology D2946 fordetailed descriptions of chrysotile and of the more commontypes of amphibole asbestos fibers.Samples must be containedin moistureproof containers from time of selection to time of1This test method is under the jurisdiction of ASTM Committee C17 onFiber-Reinforced Cement Products and is the direct responsibility of SubcommitteeC17.03 on Asbestos-Cement Sheet Products and Accessories.Current edition approved April 15,2019.Published May 2019.Originallyapproved in 1971.Last previous edition approved in 2011 as D2987 88(2011)1.DOI:10.1520/D2987_D2987M-88R19.2Available from The Asbestos Institute,http:/ referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 testing.During specimen preparation the sample should beconed and quartered without delay to avoid changing therepresentative moisture of the sample at the sampling location.(WarningSee 1.2.)7.Procedure7.1 Weigh out three 50-g test specimens to the nearest 0.01g simultaneously and spread them ev

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开